C-2007626 Datasheet, PDF (1/5 Pages) TE Connectivity Ltd – THIS DRAWING IS A CONTROLLED DOCUMENT.

8
THIS DRAWING IS UNPUBLISHED.
C ^{COPYRIGHT 2008}
TE CONNECTIVITY
RELEASED FOR PUBLICATION
ALL RIGHTS RESERVED.
7
2008
D
3 MAX
TYP
DETAIL S
SCALE 20:1 ¹³
C
6
5
4
1 _{CAGE ASSEMBLY MATERIAL: NICKEL SILVER, 0.25 THICK}
HEAT SINK MATERIAL: ALUMINUM
HEAT SINK CLIP MATERIAL: STAINLESS STEEL
EMI SPRING MATERIAL: COPPER ALLOY
FRONT FLANGE MATERIAL: ZINC ALLOY
LIGHT PIPE MATERIAL: CLEAR POLYCARBONATE
2 _{PITCH BETWEEN PORTS OF ONE 1X4 CAGE ASSEMBLY.}
3 _{SPACING BETWEEN CAGES ON THE SAME PC BOARD, TO BE SPECIFIED BY}
CUSTOMER, MUST COMPLY WITH MINIMUM DIMENSIONS SHOWN.
4 _{REFERENCE APPLICATION SPEC 114-13218 FOR RECOMMENDED DRILL HOLE}
DIAMETER AND PLATING THICKNESS.
5 _{DATUMS AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER.}
6 _{DIMENSION C IS THE NOMINAL THICKNESS OF CUSTOMER SUPPLIED PC BOARD,}
SINGLE SIDED PC BOARD MINIMUM THICKNESS = 1.45mm
DOUBLE SIDED PC BOARD MINIMUM THICKNESS = 2.2mm PER QSFP.
7 _{HEAT SINKS, LIGHT PIPES, AND CLIP SHIPPED ASSEMBLED TO CAGE ASSEMBLY.}
CAGE ASSEMBLY MAY BE PRESSED INTO THE PCB AS SHIPPED.
8 _{DATUM -A- IS TOP SURFACE OF PC BOARD.}
9 _{DIMENSION APPLIES WITH MODULE INSERTED IN CAGE.}
10 _{UNPLATED THRU HOLE.}
11 _{MAXIMUM HEIGHT OF LED OFF BOARD: 0.9mm.}
12. MATES WITH QSFP MSA COMPATIBLE TRANSCEIVER.
13 _{SURFACE TRACES PERMITTED WITHIN THIS AREA EXCEPT WHERE CAGE STANDOFFS,}
SHOWN IN DETAIL S, CONTACT PC BOARD.
14 _{BASELINE FOR THESE DIMENSIONS IS THE CENTER OF COMPLIANT PIN HOLE.}
( 60.57 )
( 1.66 )
9_B
MAX
2.2 MAX
B
SEE DETAIL
S
2D BARCODE AND DATE CODE
15
3
2
1
LOC
DIST
GP 00
P
LTR
D
E
F
REVISIONS
DESCRIPTION
REVISED PER ECO-12-003841
REVISED PER ECO-12-005533
REVISED PER ECO-14-017735
DATE
14MAR2012
31MAR2012
3DEC2014
DWN
APVD
TY KS
JY AC
RG MC
15 _{2D BARCODE AND DATE CODE (YYWWD) MARKED ON SIDE OF CAGE ASSEMBLY.}
16 _{REFERENCE APP SPEC 114-13218 FOR GASKET THICKNESS CALCULATION.}
17 _{EMI SPRING FINISH: 2µm MINIMUM TIN}
FRONT FLANGE FINISH: 3µm MINIMUM TIN OVER 1.27µm MINIMUM NICKEL
OVER 5.08µm MINIMUM COPPER
D
HEAT SINK FINISH: NICKEL.
18 _{HEAT SINKS AND CLIPS SHIPPED ASSEMBLED TO CAGE ASSEMBLY. CAGE}
ASSEMBLY MAY BE PRESSED INTO THE PCB AS SHIPPED. LIGHT PIPES,
SHIPPED UNATTACHED, MUST BE ASSEMBLED BY CUSTOMER AFTER THE
CAGE IS SEATED IN THE PCB.
C
( 79 )
3X ( 19 )
2
B
A
4805 (3/11)
CAGE ASSEMBLY
FRONT FLANGE
EMI SPRINGS
18
13.7
PCI
2007626-3
7
23.0
NETWORKING
2007626-2
7
16.0
SAN
2007626-1
HEAT SINK
PART
B
PROFILE
NUMBER
A
THIS DRAWING IS A CONTROLLED DOCUMENT.
DIMENSIONS:
mm
MATERIAL
-
-₁
TOLERANCES UNLESS
OTHERWISE SPECIFIED:
0 PLC
1 PLC
2 PLC
3 PLC
4 PLC
ANGLES
FINISH
-
0.1
0.1
-
-
-
-
1^- 7
DWN
28FEB2008
C. VALENTINE
CHK
28FEB2008
E. BRIGHT
APVD
28FEB2008
E. BRIGHT
PRODUCT SPEC
108-2286
APPLICATION SPEC
-
WEIGHT
-
CUSTOMER DRAWING
TE Connectivity
NAME
1X4 CAGE ASSEMBLY, BEHIND BEZEL,
W/ SQUARE LIGHT PIPES AND
HEAT SINKS, QSFP
SIZE
CAGE CODE
DRAWING NO
RESTRICTED TO
A1 ⁰⁰⁷⁷⁹
2007626
SCALE
SHEET
1:1
OF
15
-
REV
F