82A6015 Datasheet, PDF (1/1 Pages) TE Connectivity Ltd – This specification sheet forms a part of the latest issue of Raychem Specification 80.

SPECIFICATION CONTROL DRAWING ^SCD
Title
TWO CONDUCTOR CABLE, SHIELDED, JACKETED,
Date
GENERAL PURPOSE, FLEXIBLE, 600 VOLT
11-5-14
This specification sheet forms a part of the latest issue of Raychem Specification 80.
82A6015
Revision
A
COMPONENT WIRES - 82A0114
SHIELD - SILVER-COATED COPPER
JACKET - RADIATION-CROSSLINKED,
MODIFIED FLEXIBLE ETFE
PART NUMBER
1/
82A6015-28-*
82A6015-26-*
82A6015-24-*
82A6015-22-*
CONDUCTOR
SIZE
(AWG)
28
26
24
22
CABLE CONSTRUCTION DETAILS
SHIELD
SIZE
(AWG)
38
38
38
38
JACKET THICKNESS
(inch)
MINIMUM
.005
.006
.006
.007
NOMINAL
.008
.009
.009
.010
OUTSIDE DIAMETER
(inch)
NOMINAL
.091
.101
.109
.123
MAXIMUM
.096
.106
.114
.129
MAXIMUM
WEIGHT
(lbs/1000 ft.)
6.9
8.5
10.5
13.3
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 150°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
CROSSLINKING PROOF TEST: 300 ± 3°C for 1 hour
DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz
JACKET COLOR: White preferred
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 100% (minimum)
Tensile Strength, 3000 lbf/in² (minimum)
JACKET FLAWS:
Spark Test, 1500 volts (rms)
Impulse Dielectric Test, 6.0 kV (peak)
SECANT MODULUS (Test per ASTM D 882):
4.0 x 10⁴ lbf/in² (maximum),
2% strain, 2 inch jaw separation, 0.2 inch/minute
SHIELD COVERAGE: 85% (minimum)
VOLTAGE WITHSTAND (Post Environmental):
1000 volts (rms), 60 Hz, 1 minute
1/ PART NUMBER:
The "*" in the part numbers above shall be replaced by color
code designators with a slash separating the component wire
colors and a dash separating the component wire colors from
the jacket color.
Example: AWG 24, black and brown component wires;
white jacket: 82A6015-24-0/1-9
NOTE: Nominal values are for information only. Nominal values are not requirements.
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: "901/902..." MAY BE REPLACED BY "Axxx".) OTHER CODES AND
SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
Page 1 of 1
Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.
DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
Raychem Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: [phone]
Fax: [phone]
© 2014 Tyco Electronics Corporation. All rights reserved.