55PC6362 Datasheet, PDF (1/1 Pages) TE Connectivity Ltd – This specification sheet forms a part of the latest issue of Raychem Specification 55PC.

SPECIFICATION CONTROL DRAWING
SCD
55PC6362
Title
TWO CONDUCTOR CABLE, SHIELDED, JACKETED, GENERAL PURPOSE, 600 VOLT
Date
4-9-15
Revision
A
This specification sheet forms a part of the latest issue of Raychem Specification 55PC.
COMPONENT WIRES - 55PC0214
SHIELD - NICKEL-COATED COPPER
JACKET - RADIATION-CROSSLINKED,
MODIFIED ETFE
PART NUMBER
1/
55PC6362-24-*
55PC6362-22-*
55PC6362-20-*
55PC6362-18-*
55PC6362-16-*
CONDUCTOR
SIZE
(AWG)
24
22
20
18
16
SHIELD
SIZE
(AWG)
38
38
38
38
38
CABLE CONSTRUCTION DETAILS
JACKET THICKNESS
(inch)
OUTSIDE DIAMETER
(inch)
LOWER SPEC
LIMIT
TARGET
WALL
LOWER SPEC
LIMIT
TARGET
VALUE
UPPER SPEC
LIMIT
.0050
.0065
.105
.109
.113
.0055
.0070
.118
.122
.127
.0055
.0070
.135
.139
.144
.0055
.0070
.154
.158
.163
.0060
.0075
.169
.174
.179
WEIGHT
(lbs/1000 ft.)
TARGET
VALUE
UPPER SPEC
LIMIT
9.34
12.02
16.02
21.57
26.21
9.75
12.50
16.56
22.25
26.96
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 200°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
CROSSLINK VERIFICATION: 300 ± 3°C for 1 hour
DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz
JACKET COLOR: White preferred
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 50% (minimum)
Tensile Strength, 5000 lbf/in² (minimum)
JACKET FLAWS:
Spark Test, 1000 volts (rms)
Impulse Dielectric Test, 6.0 kV (peak)
SHIELD COVERAGE: 85% (minimum)
VOLTAGE WITHSTAND (Post Environmental):
1000 volts (rms), 60 Hz, 1 minute
1/ PART NUMBER:
The "*" in the part numbers above shall be replaced by color code
designators with a slash separating the component wire colors and a dash
separating the component wire colors from the jacket color.
Example: AWG 22, red and blue component wires; white jacket:
55PC6362-22-2/6-9
Page 1 of 1
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: "901/902..." MAY BE REPLACED BY "Axxx".) OTHER CODES
AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.
DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL.
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
Raychem Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: [phone]
Fax: [phone]
© 2015 Tyco Electronics Corporation. All rights reserved.