55A1126 Datasheet, PDF (1/1 Pages) TE Connectivity Ltd – This specification sheet forms a part of the latest issue of Raychem Specification 55A.

SPECIFICATION CONTROL DRAWING ^SCD
Title
Date
TWO CONDUCTOR CABLE, SHIELDED, JACKETED, 600 VOLT
10-25-16
This specification sheet forms a part of the latest issue of Raychem Specification 55A.
55A1126
Revision
C
COMPONENT WIRES - 55A0116
SHIELD - NICKEL-COATED COPPER
JACKET - RADIATION-CROSSLINKED,
MODIFIED ETFE
PART NUMBER
1/
55A1126-28-*
55A1126-26-*
55A1126-24-*
55A1126-22-*
55A1126-20-*
55A1126-18-*
55A1126-16-*
CONDUCTOR
SIZE
(AWG)
28
26
24
22
20
18
16
CABLE CONSTRUCTION DETAILS
SHIELD
SIZE
(AWG)
38
38
38
38
38
38
38
JACKET THICKNESS
(inch)
MINIMUM
.006
.006
.006
.006
.006
.006
.006
NOMINAL
.008
.008
.008
.008
.008
.008
.008
OUTSIDE DIAMETER
(inch)
NOMINAL
.087
.097
.107
.119
.133
.153
.169
MAXIMUM
.092
.102
.112
.125
.140
.161
.177
MAXIMUM
WEIGHT
(lbs/1000 ft.)
6.3
7.9
9.8
12.4
16.4
22.1
27.0
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 200°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
ACCELERATED AGING: 300 ± 3°C for 7 hours
BLOCKING: 200 ± 3°C for 6 hours
DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz
FLAMMABILITY: Procedure 1,
3 seconds (maximum), 3 inches (maximum);
no flaming of facial tissue
JACKET COLOR: White preferred
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 50% (minimum)
Tensile Strength, 5000 lbf/in² (minimum)
JACKET FLAWS:
Spark Test, 1000 volts (rms)
Impulse Dielectric Test, 6.0 kV (peak)
LIFE CYCLE: 230 ± 3°C for 500 hours
LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours
SHIELD COVERAGE: 85% (minimum)
VOLTAGE WITHSTAND (Post Environmental):
1000 volts (rms), 60 Hz, 1 minute
1/ PART NUMBER:
The "*" in the part numbers above shall be replaced by color
code designators with a slash separating the component wire
colors and a dash separating the component wire colors from
the jacket color.
Example: AWG 24, blue and white component wires;
white jacket: 55A1126-24-6/9-9
NOTE: Nominal values are for information only. Nominal values are not requirements.
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: "901/902..." MAY BE REPLACED BY "Axxx".) OTHER CODES AND
SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
Page 1 of 1
Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.
DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
Raychem Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: [phone]
Fax: [phone]
© 2016 Tyco Electronics Corporation. All rights reserved.