408-4064 Datasheet, PDF (1/5 Pages) TE Connectivity Ltd – PRO-CRIMPER III Hand Crimping Tool Assembly And Die Set

PRO-CRIMPER* III Hand
Crimping Tool Assembly And
Die Set 58517-[ ]
Instruction Sheet
408-4064
10 MAY 12 Rev F
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Locator
(Supplied with
Die Assembly)
Stationary Jaw
Back of Tool
(Wire Side)
Front of Tool
(Locator Side)
Die Assembly ^{Moving Jaw}
Ratchet Adjustment Wheel
The PRO-CRIMPER III Hand Crimping Tool is a “Commercial” grade tool
and is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate Application Specification (114-series), but may not comply
with other feature parameters of the specification. TE Connectivity offers a
variety of tools to satisfy your performance requirements. For additional
information, contact the Tooling Assistance Center at 1-800-722-1111.
Pivot Pin
PRO-CRIMPER III
Hand Crimping
Tool Frame
354940-1
(Instruction
Sheet 408-9930)
Handle
Moving
Jaw
PRO-CRIMPER DIE ASSEMBLY
III HAND TOOL PART NUMBER
58517-1
58517-2
58517-3
58517-4
None
58517-5 •
• Bench Machine/Battery and
SDE-SA Hand Tool Only
LOCATOR
PART
NUMBER‡
CONTACT
FAMILY
189590-1
CST 100
1424907-1
CST 100 II
1901843-1
CST 100 II
‡ Supplied with the die assembly. Also available
separately.
SIZE
(AWG)
WIRE
INSUL DIA
(mm [in.])
STRIP LENGTH
(mm [in.])
26-22
0.89-1.65
[.035-.065]
2.54-2.92
[.100-.125]
‡‡ Contact the PRODUCT INFORMATION CENTER for specific contact part
numbers.
Figure 1
1. INTRODUCTION
PRO-CRIMPER III Hand Crimping Tool Assembly
58517-1 consists of Die Assembly 58517-2 and
PRO-CRIMPER III Hand Tool Frame 354940-1. See
Figure 1.
The die assembly consists of crimping dies and a
locator assembly.
Read these instructions thoroughly before crimping
any contacts.
NOTE
i
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures and
illustrations are for identification only and are not
drawn to scale.
Reasons for reissue are provided in Section 11,
REVISION SUMMARY.
2. DESCRIPTION (See Figure 1 and Figure 2.)
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full contact crimping.
The tool frame holds a die assembly with one crimping
section.
The die assembly features a wire anvil, an insulation
anvil, a wire crimper, and an insulation crimper.
Attached to the outside of the frame is a locator, which
holds and helps to position the contact.
©2012 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
*Trademark
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
1 of 5
LOC B