408-10376 Datasheet, PDF(1/2 Page) TE Connectivity Ltd

English

English German Russian Spanish Italian Polish Chinese Japanese Korean French Portuguese	Language :

408-10376 Datasheet, PDF (1/2 Pages) TE Connectivity Ltd – Extraction Tool 2063388- 1

Extraction Tool 2063388- 1

Instruction Sheet

408- 10376

23 Mar 11 Rev B

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume

applications. A wide selection of powered application equipment for extended- use, production operations is available.

Handle

Plunger

Sheet 408--9501. The pin and socket contacts are

listed by part number in Figure 1. Read these

instructions thoroughly before attempting to remove

any contacts from the housings.

Tip

NOTE

Dimensions on this sheet are in millimeters [with

inch equivalent dimensions in brackets]. Figures

and illustrations are for identification only and are

not drawn to scale.

PART NUMBERS

FOR MINIATURE RECTANGULAR (MR) CONTACTS

SOCKET

STRIP

350018

350036

350019

350037

350171

350197

350184

350186

350183

350185

350665

350666

350663

350664

350696

350697

350684

350685

-- -- --

350694

350695

-- -- --

350968

640579

641294

641300

350967

640545

-- -- --

FOR MINIATURE UNIVERSAL MATE- N- LOK* CONTACTS

SOCKET

STRIP

170359

170363

170361

170365

170360

170364

170362

170366

171636

171638

171637

171639

FOR COMMERCIAL PIN .062 CONTACTS

STRIP

350629

-- -- --

640391

-- -- --

Figure 1

1. INTRODUCTION

Extraction Tool 2063388--1, Figure 1, is designed to

remove Miniature Rectangular (MR) contacts,

Miniature Universal MATE--N--LOK contacts, or

Commercial .062 pin contacts from the housings

designed for these contacts. Information for the

removal of Commercial .062 socket contacts with

Extraction Tool 844134--1 can be found on Instruction

2. DESCRIPTION

The tool consists of a metal tip and a plastic handle. The

tip is inserted into the mating face of the housing,

depressing the locking lances of the crimped contact.

This action allows the contact to be extracted from the

wire--entry face of the housing.

3. EXTRACTION PROCEDURE

The procedures which follow are recommended to

extract a crimped contact from a housing. See Figures

2 and 3.

Proceed as follows:

1. Grasp wire of contact to be removed. Push

contact toward mating face of connector and hold

in this position. This will disengage contact locking

lance from shoulder of cavity.

2. While holding wire, place tool releasing barrel

over end of contact and push straight into cavity

until it bottoms. The locking lance is now released.

3. Keep releasing barrel firmly bottomed in cavity

and depress plunger (handle). Contact will partially

eject.

NOTE

If difficulty is encountered in pushing contact

forward, Insertion Tool 91002- 1 (tweezer type),

may be used to perform the task from the wire

side of the housing.

4. Pull contact from BACK of connector and

remove tool from cavity.

NOTE

Before inserting contact into housing, reset

locking lances to their original positions. Consult

the Customer Drawing covering the specific

contact removed (or consult TE Connectivity

Engineering) for correct setting of locking lances.

E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1--800--722--1111

PRODUCT INFORMATION 1--800--522--6752

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.

*Trademark. Other logos, product and/or Company names may be trademarks of their respective owners.

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

1 of 2

LOC B

▷