10613 Datasheet, PDF (1/1 Pages) TE Connectivity Ltd – THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200.

SPECIFICATION CONTROL DRAWING
CHEMINAX
77 OHM, AWG 24, 19 STRANDS OF AWG 36,
OPTIMIZED DOUBLE SHIELDS, DATA BUS CABLE, MIL-STD-1553
Date:
Revision:
10613
3-5-15
S
THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200.
CONSTRUCTION DETAILS
ELECTRICAL CHARACTERISTICS
DIMENSIONS ARE NOMINAL VALUES IN INCHES, UNLESS OTHERWISE _{CHARACTERISTIC IMPEDANCE}
DESIGNATED.
MUTUAL CAPACITANCE
77 ± 5 ohms, Method C at 1 MHz
30.0 pF/ft. (98.4 pF/m) (maximum)
.0250
(.635 mm)
.048 ± .002
(1.22 ± .05 mm)
.032
(.813 mm)
ATTENUATION
1.4 dB/100 ft. (4.59 dB/100 m) (maximum)
at 1 MHz
CONDUCTORS
AWG 24,
19 Strands of AWG 36,
Silver-Coated High-
SURFACE TRANSFER IMPEDANCE 10 milliohms/meter (maximum)
(Per SAE AS85485)
at 30 MHz
ADDITIONAL REQUIREMENTS
Strength Copper Alloy
COMPONENT WIRE PRIOR TO CABLING
DIELECTRICS
(Test procedures per SAE AS22759)
Radiation-Crosslinked, _{CONDUCTOR RESISTANCE}
Modified ETFE
Colors - Light Blue/White ^{CROSSLINKING PROOF TEST}
FILLERS
Radiation-Crosslinked,
Modified ETFE
INSULATION (DIELECTRIC)
ELONGATION
TENSILE STRENGTH
26.5 ohms/1000 ft. (86.9 ohms/km) (nominal)
300 ± 3°C for 1 hour,
.625 inch (15.9 mm) mandrel,
.375 lb (170 g), 2.5 kV dielectric test
50% (minimum)
5000 lbf/in² (34.5 N/mm²) (minimum)
INSULATION FLAWS
SPARK TEST
IMPULSE TEST
3.0 kV (rms)
8.0 kV (peak)
INSULATION RESISTANCE
5000 megohms for 1000 ft.
(1524 megohms-km) (minimum)
.113
(2.87 mm)
.130
(3.30 mm)
1st SHIELD
AWG 38,
Tin-Coated Copper,
Optimized
2nd SHIELD
AWG 38,
Tin-Coated Copper,
Optimized
LOW TEMPERATURE-COLD BEND -65 ± 3°C for 4 hours,
.750 inch (19.1 mm) mandrel,
1.00 lb (454 g), 2.5 kV dielectric test
SHRINKAGE
200 ± 3°C for 1 hour,
.125 inch (3.18 mm) (maximum)
in 12 inches (305 mm)
FINISHED CABLE
(Test procedures per NEMA WC 27500, unless otherwise specified)
BLOCKING
200°C for 6 hours
CABLE LAY LENGTH
.75 inch (19.1 mm) (minimum),
1.25 inches (31.8 mm) (maximum)
CROSSLINKED VERIFICATION
300 ± 5°C for 6 hours,
6.00 inch (152 mm) mandrel
.146 (3.71 mm)
(nominal)
.154 (3.91 mm)
(maximum)
JACKET
Radiation-Crosslinked,
Modified ETFE
FLAMMABILITY
(Method B of Spec 1200)
JACKET
ELONGATION
TENSILE STRENGTH
3 seconds (maximum);
3 inches (76.2 mm) (maximum);
no flaming of facial tissue
50% (minimum)
5000 lbf/in² (34.5 N/mm²) (minimum)
JACKET FLAWS
SPARK TEST
IMPULSE TEST
1.0 kV (rms)
6.0 kV (peak)
JACKET THICKNESS
.008 inch (.203 mm) (nominal)
LOW TEMPERATURE-COLD BEND -55 ± 5°C for 4 hours,
6.00 inch (152 mm) mandrel
VOLTAGE WITHSTAND
(DIELECTRIC)
1500 volts (rms)
Designate outer jacket color with a dash number in accordance with ^WEIGHT
26.2 lbs/1000 ft. (39.0 kg/km) (maximum)
MIL-STD-681. Unless otherwise specified, outer jacket color will be
white (designated by a "-9" appended to the part number and
CABLE IDENTIFICATION: Outer jacket shall be marked in contrasting color at 12
conductor AWG size, e.g. 10613-24-9).
inch (305 mm) (nominal) intervals between marks as follows: "10613 RAYCHEM"
Other codes and suffixes may be added to the part number, as
ENGINEERING REFERENCE
necessary, to capture any additional requirements imposed by the _{TEMPERATURE RATING}
purchase order.
150°C (maximum)
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also
reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
Page 1 of 2
Page 2 is for internal use only.
Cheminax, Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.
Raychem Wire & Cable
501 Oakside Avenue
Redwood City, California 94063-3800
Phone: [phone] Fax: [phone]
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
© 2009-2015 Tyco Electronics Corporation. All rights reserved.