HFE2500 Datasheet, PDF (2/2 Pages) TDK Electronics – 2500W 1U Front End Power Supplies

HFE2500 Series
Model Selector
Model
Output
Voltage
Adjust
Range⁽¹⁾
HFE2500-12
12V
9.6 - 13.2V
HFE2500-12/S
12V
9.6 - 13.2V
HFE2500-24
24V
19.2 - 29V
HFE2500-24/S
24V
19.2 - 29V
HFE2500-48
48V
38.4 - 58V
HFE2500-48/S
48V
38.4 - 58V
Model
Load
Reg
Line
Reg
HFE2500-12
60mV
30mV
HFE2500-12/S
60mV
30mV
HFE2500-24
120mV
60mV
HFE2500-24/S 120mV
60mV
HFE2500-48
240mV
120mV
HFE2500-48/S 240mV
120mV
(3) At 75% load, 100 / 230VAC input
Max Current
(Vin>170VAC)
200A
200A
104A
104A
52A
52A
Ripple &
Noise⁽¹⁾
240mV
240mV
240mV
240mV
480mV
480mV
Max Power
(Vin>170VAC)
2400W
2400W
2496W
2496W
2496W
2496W
Efficiency
(%)⁽³⁾
90 / 92%
90 / 92%
90 / 92%
90 / 92%
91 / 93%
91 / 93%
Max Current
(100<Vin<170VAC)⁽²⁾
125A
125A
62A
62A
31A
31A
I²C
-
Yes
-
Yes
-
Yes
Max Power
(100<Vin<170VAC)⁽²⁾
1500W
1500W
1488W
1488W
1488W
1488W
Accessories
Model
HFE2500-S1U
Description
Four slot 19” rack, IEC320-C20 input connector
HFE2500-S1U-TB
HFE2500/BP
Four slot 19” rack, Terminal Block input connector
One slot blanking panel, two provided with each rack
Maximum Rack Current
320A each side (640A total)
320A each side (640A total)
-
Outline HFE2500S1U
273.6
88.5
214.5
M5 HOLES FOR
MOUNTING BRACKETS.
4 PLACES
17.0 TYPx2
82.5
61.0
SEE NOTE 3.
OUTPUT
BUS BAR "-V"
OUTPUT
BUS BAR "+V"
22.0 TYP x2
MODULE "A"
MODULE "B"
MODULE "C"
13.0 TYPx2
13.0 TYP x2
SEE NOTE 2.
PMBUS ADRESS
SEE NOTE 4.
OUTPUT
BUS BAR "-V"
OUTPUT
BUS BAR "+V"
MODULE "D"
125.8
SEE NOTE 5.
MODEL KEY
FOR DIFFERENT
OUTPUT VOLTAGE
MODELS.
MODULE "A" _{MODULE "B" MODULE "C" MODULE "D"}
AIR FLOW
DIRECTION
CONNECTOR DESCRIPTION: IPLT1-120-01-L-D-RA(SAMTEC)
SIGNALS & CONTROL CONNECTOR PINS ASSIGNMENT
MATING CONNECTOR: IPD1-20-D (SAMTEC)
40
2
39
1
HOLES FOR BLANK
PANEL MOUNTING.
USE FLAT HEAD SCREW
M3x6 8 PLACES
MARKED "A"
A
A
445.0 ±1.0
483.0 ±1.0
466.2 ±1.0
A
A
NOTES
1. MOUNTING HOLES FOR RACK 19". USE M6x12 SCREWS TO FIX THE
UNIT TO A RACK.
2. USE NUT,FLAT WASHER AND SPRING WASHER FOR LOAD WIRES
FIXING. USE LUG STUD M6 FOR LOAD WIRES.RECOMMENDED
TORQUE: 42-56 Kgf.cm
SEE NOTE 1. 3. TO FIX THE MOUNTING BRACKET TO THE CHASSIS USE M5x10 SEMS
SCREWS .RECOMMENDED TIGHTENING TORQUE 27~31Kgf.cm.
SCREWS MUST NOT PENETRATE THE CHASSIS MORE THAN 6.0 mm.
4. REFER TO INSTRUCTION MANUAL FOR SETTING DETAILS.
5. MODEL NAME, VOLTAGE AND CURRENT RATING AND
SAFETY APPROVALS SYMBOLS WILL BE SHOWN HERE
ACCORDING TO THE SPECIFICATION.
6. THE HFE-S1U RACK IS SHOWN WITH 4 HFE2500
UNITS INSTALLED.
For Additional Information, please visit
us.tdk-lambda.com/lp/products/hfe-series.htm
1-800-526-2324 • www.us.tdk-lambda.com/lp/
59
Revision A6: Oct 2012