DRV2605EVM-BT Datasheet, PDF (32/34 Pages) TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS – evaluation kit for the DRV2605 ERM and LRA Haptic Driver.

Schematics, PCB Layers, and Bill of Materials
www.ti.com
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES (continued)
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意く
ださい。
1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備
でご使用いただく。
2. 実験局の免許を取得後ご使用いただく。
3. 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものと
します。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4 EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT
NOT LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to
handling or using the EVM, including without limitation any warning or restriction notices. The notices contain important
safety information related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in
the user guide, other available documentation provided by TI, and any other applicable requirements and employ
reasonable and customary safeguards. Exceeding the specified performance ratings and specifications
(including but not limited to input and output voltage, current, power, and environmental ranges) for the EVM
may cause personal injury or death, or property damage. If there are questions concerning performance ratings
and specifications, User should contact a TI field representative prior to connecting interface electronics including
input power and intended loads. Any loads applied outside of the specified output range may also result in
unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or interface
electronics. Please consult the EVM user guide prior to connecting any load to the EVM output. If there is
uncertainty as to the load specification, please contact a TI field representative. During normal operation, even
with the inputs and outputs kept within the specified allowable ranges, some circuit components may have
elevated case temperatures. These components include but are not limited to linear regulators, switching
transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may
become very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with
the dangers and application risks associated with handling electrical mechanical components, systems, and
subsystems. User assumes all responsibility and liability for proper and safe handling and use of the EVM by
User or its employees, affiliates, contractors or designees. User assumes all responsibility and liability to ensure
that any interfaces (electronic and/or mechanical) between the EVM and any human body are designed with
suitable isolation and means to safely limit accessible leakage currents to minimize the risk of electrical shock
hazard. User assumes all responsibility and liability for any improper or unsafe handling or use of the EVM by
User or its employees, affiliates, contractors or designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international,
federal, state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User
assumes all responsibility and liability for compliance in all respects with such laws and regulations. User assumes all
responsibility and liability for proper disposal and recycling of the EVM consistent with all applicable international,
federal, state, and local requirements.
5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as
accurate as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information
on its websites as accurate, complete, reliable, current, or error-free.
32 DRV2605EVM-BT User's Guide
Copyright © 2014, Texas Instruments Incorporated
SLOU391 – May 2014
Submit Documentation Feedback