HV9100 Datasheet, PDF (1/7 Pages) Supertex, Inc – High-Voltage Switchmode Controllers with MOSFET

HV9100
HV9102
HV9103
High-Voltage Switchmode Controllers with MOSFET
Ordering Information
+V_IN
Min Max
10V 70V
Feedback
Max
Voltage Duty Cycle
± 1.0%
49%
MOSFET Switch
BV_DSS
150V
R_{DS (ON)}
5.0Ω
10V 120V ± 1.0%
49%
200V
7.0Ω
10V 120V ±1.0%
99%
200V
7.0Ω
Standard temperature range for all parts is industrial (-40° to +85°C).
Package Options
14 Pin Plastic DIP 20 Pin Plastic PLCC
HV9100P
HV9100PJ
HV9102P
HV9102PJ
HV9103P
HV9103PJ
Features
General Description
❏ 10 to 120V input range
❏ 200V, 7.0Ω output MOSFET
❏ Current-Mode Control
❏ High Efficiency
❏ Up to 1MHz Internal Oscillator
❏ Internal Start-up Circuit
Applications
❏ DC/DC Converters
❏ Distributed Power Systems
❏ ISDN Equipment
❏ PBX Systems
❏ Modems
The Supertex HV9100 through HV9103 are a series of BiCMOS/
DMOS single-output, pulse width modulator ICs intended for use
in high-speed high-efficiency switchmode power supplies. They
provide all the functions necessary to implement a single-switch
current-mode PWM, in any topology, with a minimum of external
parts.
Utilization of Supertex proprietary BiCMOS/DMOS technology
results in a device with one tenth of the operating power of
conventional bipolar PWM ICs, which can operate at more than
twice their switching frequency. Dynamic range for regulation is
also increased, to approximately 8 times that of similar bipolar
parts. They start directly from any DC input voltage between 10
and 70VDC for the HV9100 or 10 to 120VDC for the HV9102 and
HV9103, requiring no external power resistor. The output stage
for the HV9100 is a 150V, 5.0 ohm MOSFET and for the HV9102
and HV9103 is a 200V, 7.0 ohm MOSFET. The clock frequency
is set with a single external resistor.
Accessory functions are included to permit fast remote shutdown
(latching or nonlatching), and undervoltage shutdown.
Absolute Maximum Ratings
+V_IN, Input Voltage
120V
V_DS
200V
V_DD, Logic Voltage
15.0V
Input Voltage Logic, Linear, FB and Sense -0.3V to V_DD+0.3V
I_D (Peak)
2.5A
Storage Temperature
-65°C to 150°C
Power Dissipation, Plastic DIP
750mW
Power Dissipation, PLCC
1400mW
For detailed circuit and application information, please refer
to application notes AN-H13 and AN-H21 to AN-H24.
11/12/01
Supertex Inc. does not recommend the use of its products in life support applications and will not knowingly sell its products for use in such applications unless it receives an adequate "products liability
indemnification insurance agreement." Supertex does not assume responsibility for use of devices described and limits its liability to the replacement of devices determined to be defective due to
workmanship. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the
Supertex website: http://www.supertex.com. For complete liability information on all Supertex prod₁ucts, refer to the most current databook or to the Legal/Disclaimer page on the Supertex website.