|
RGA Datasheet, PDF (1/2 Pages) Surge Components – rohs compliance | |||
|
Aluminum Electrolytic Capacitors
RGA
RGA Series
Features
â§105â, 2,000 hours assured
â§105â standard series for general purposes
â§RoHS Compliance
â§If there is any requirement on ESR, itâs suggested to use low
ESR series instead of RGA. Please consult us for any inquiry.
Specifications
Items
Category Temperature Range
Capacitance Tolerance
6.3~400V
-40â ~ +105â
Performance
±20%
Sleeve & Marking Color: Black & White
450V
-25â ~ +105â
(at 120Hz, 20â)
Leakage Current (at 20â)
Rated voltage
â¦100V
Time
after 2 minutes
Leakage Current
I = 0.01CV or 3 (μA)
whichever is greater
Where, C = rated capacitance in μF
ï¼100V
after 5 minutes
CV ⦠1,000
I = 0.03CV + 15(μA)
CV ï¼ 1,000
I = 0.02CV + 25(μA)
V = rated DC working voltage in V
Tanδ (at 120 Hz, 20â)
Low Temperature
Characteristics (at 120Hz)
Rated Voltage 6.3 10 16 25 35 50 63 100 160 200 250 350 400 450
Tanδ (max) 0.23 0.20 0.16 0.14 0.12 0.10 0.09 0.08 0.12 0.14 0.17 0.20 0.25 0.25
When the capacitance exceeds 1,000μF, 0.02 shall be added every 1,000μF increase.
Impedance ratio shall not exceed the values given in the table below.
Rated Voltage
6.3 10 16 25 35 50 63 100 160 200 250 350 400 450
Z(-25â) ÏDï¼16 4
Impedance /Z(+20â) ÏDâ§16 6
3
4
3
4
2
3
2
3
2
3
2
3
2
3
3
6
8 12 14 16
Ratio
Z(-40â) ÏDï¼16 8 6 6
/Z(+20â) ÏDâ§16 12 10 8
4
8
4
8
3
8
3
6
3
6
4
8 10 16 18 -
Endurance
Shelf Life Test
Ripple Current &
Frequency Multipliers
Test Time
2,000 Hrs
Capacitance Change
Within ±20% of initial value
Tanδ
Less than 200% of specified value
Leakage Current
Within specified value
* The above Specifications shall be satisfied when the capacitors are restored to 20â after the rated voltage applied with rated
ripple current for 2,000 hours at 105â.
Test Time
1,000 Hrs
Capacitance Change
With in ±20% of initial value
Tanδ
Less than 200% of specified value
Leakage Current
Within specified value
* The above Specifications shall be satisfied when the capacitors are restored to 20â after exposing them for 1,000 hours at
105â without voltage applied. The rated voltage shall be applied to the capacitors before the measurements for 160 ~ 450V
(Refer to JIS C 5101-4 4.1).
Cap. (μF)
Freq. (Hz) 60 (50)
120
500
1k
10k up
Under 100
0.70
1.00
1.30
1.40
1.50
100 ï¼ C ⦠1,000
0.75
1.00
1.20
1.30
1.35
1,000 up above
0.80
1.00
1.10
1.12
1.15
Diagram of Dimensions
Ventâ§6.3Ï
L+α max
ÏD+βmax
Sleeve
15 min
4 min
Lead Spacing and Diameter
ÏD 5 6.3 8 10 12.5 16 18
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5
Ïd
0.5
0.6
0.8
α
L<20: 1.5, Lâ§20: 2.0
β
0.5
Unit: mm
22 25
10 12.5
1.0
2.0
The case size of 12.5Ã16, 16Ã16, 16Ã20, 18Ã16, 18Ã20 and 18Ã25 are suitable for below diagram:
Vent
L+α max
ÏD+βmax
Sleeve
15 min
4 min
80
All product specifications in the catalog are subject to change without notice. (CAT. 2014E1)
|
▷ |