KBU6A Datasheet, PDF (1/2 Pages) Pan Jit International Inc. – SILICON SINGLE-PHASE BRIDGE RECTIFIER(VOLTAGE - 50 to 800 Volts CURRENT - 6.0 Amperes)

KBU6A-KBU6M
SINGLE-PHASE BRIDGE RECTIFIERS
VOLTAGE RANGE: 50 - 1000V
CURRENT: 6.0 A
Features
! Ideal for printed circuit boards
! High surge current capability
! ^{High case dielectric strength of 1500 V}RMS
Mechanical Data
! _{Case : Molded plastic}
! _{Polarity : Polarity symbols marked on case}
! ^{Mounting position : Any}
! ^{Weight : 8.0 grams}
KBU
.933(23.7)
.894(22.7)
.160(4.1)
.140(3.6)
.700(17.8)
.760(19.3)Max .660(16.8)
+
+
.075(1.9)R.TYP.
_
(2 PLACES)
~ ~+
.185(4.7)
.165(4.2)
45⁰
.085(2.2)
.065(1.7)
.455(11.3)
.405(10.3)
1.0(25.4)Min
.220(5.6)
.180(4.6)
.260(6.6)
.180(4.5)
.280(7.1)
.260(6.6)
.205(5.2)
.185(4.7)
.052(1.3)
.048(1.2)
inch (mm)
Maximum Ratings and Electrical Characteristics ^TA ^{= 25°C unless otherwise specified}
Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%.
Characteristic
Symbol
Maximum repetitive peak reverse voltage
VRRM
Maximum RMS voltage
VRMS
Maximum DC blocking voltage
VDC
Maximum average forward rectified TC=100°C (NOTE 1, 2)
output current at
TA=40°C (NOTE 3)
I(AV)
Peak forward surge current single half sine-wave
superimposed on rated load (JEDEC Method)TJ=150°C ^IFSM
Maximum instantaneous forward voltage drop
per leg at 6.0A
VF
Maximum DC reverse current
at rated DC blocking voltage per leg
TA=25°C
TA=125°C
IR
Typical thermal resistance per leg (NOTE 2)
RΘJA
RΘJC
Operating junction and storage temperature range
TJ, TSTG
KBU
6A
50
35
50
KBU
6B
100
70
100
KBU
6D
200
140
200
KBU
6G
400
280
400
6.0
6.0
250.0
KBU
6J
600
420
600
1.0
5.0
1.0
8.6
3.1
-50 to +150
KBU
6K
800
560
800
KBU
6M
Unit
1000 Volts
700 Volts
1000 Volts
Amps
Amps
Volts
µA
mA
°C/W
°C
NOTES:
(1) Recommended mounted position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw
(2) Thermal resistance from junction to ambient with units in free air, P.C.B. mounted on 0.5 x 0.5” (12 x 12mm) copper pads, 0.375" (9.5mm) lead length
(3) Thermal resistance from junction to case with units mounted on a 2.6 x 1.4 x 0.06" thick (6.5 x 3.5 x.15cm) Al. Plate
1 of 2
www.sunmate.tw