STLC5444 Datasheet, PDF (6/17 Pages) STMicroelectronics – QUAD FEEDER POWER SUPPLY

STLC5444
SWITCHING CHARACTERISTICS (VBB = -54V; VCC = 5V; unless otherwise specified)
MICROPROCESSOR READ/WRITE TIMING NON MULTIPLEXED MODE (for references see figure 1a
and 2b).
Symbol
Parameter
Min.
t_RLRH RD, CS pulse width
260
t_RHRL RD, recovery time
T _amb: 0 to 70°C
200
T _amb: -40 to 0°C and +70°C to +85°C
220
t_RLDA RD, CS low to data available
t_RHDZ
RD or CS high to data Z
T_amb: 0 to 70°C
T _amb: -40 to 0°C and +70°C to +85°C
t_ASRL Address setup time to READ active
0
t_AHRH Address hold time to READ inactive
0
t_ASWL Address setup time to WRITE active
30
t_AHWH Addess hold time to WRITE inactive
50
t_ADDA Address stable to data available
T_amb: 0 to 70°C
360
T _amb: -40 to 0°C and +70°C to +85°C
390
t_WLWH WR or CS pulse width
200
t_WHWL Write recovery time
200
t_DAWH Data setup time
100
t_WHDZ Data hold time
T _amb: 0 to 70°C
20
T _amb: -40 to 0°C and +70°C to +85°C
40
t_RES Reset Pulse with
200
Note: AC timings are tested at 0.8V and 2V with input levels of 0.4V and 2.4V.
Max.
260
130
160
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
SWITCHING CHARACTERISTICS (VBB = -54V; VCC = 5V; unless otherwise specified)
MICROPROCESSOR READ/WRITE TIMING MULTIPLEXED MODE (for references see figure 1 and 2).
Symbol
Parameter
Min.
t_RLRH RD, CS pulse width
260
t_RHRL RD, recovery time
T _amb: 0 to 70°C
200
T _amb: -40 to 0°C and +70°C to +85°C
220
t_RLDA RD, CS low to data available
t_RHDZ
RD or CS high to data Z
T_amb: 0 to 70°C
T _amb: -40 to 0°C and +70°C to +85°C
tAHAL ALE pulse width
100
t_ADAL Address setup time
60
t_ADAZ Address hold time
50
t_AZRL Address Z to RD low
0
t_AZWL Address Z to WR Low
0
t_ADDA Address stable to data available
T_amb: 0 to 70°C
360
T _amb: -40 to 0°C and +70°C to +85°C
390
t_WLWH WR or CS pulse width
200
t_WHWL Write recovery time
200
t_DAWH Data setup time
100
t_WHDZ Data hold time
T _amb: 0 to 70°C
20
T _amb: -40 to 0°C and +70°C to +85°C
40
t_RES Reset Pulse with
200
Note: AC timings are tested at 0.8V and 2V with input levels of 0.4V and 2.4V.
Max.
260
130
160
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Si Timing (at 10% of final value)
Symbol
t_EN
t_DIS
Parameter
Test condition
Si output enable time (from LER)
R_LOAD = 3kΩ
Si output disable time (from LER or RESET)
Typ.
2
3
Max.
5
6
Unit
µs
µs
6/17