M24512-A125 Datasheet, PDF (28/40 Pages) STMicroelectronics – Automotive 512-Kbit serial IC bus EEPROM with 1 MHz clock

DC and AC parameters
M24512-A125
Symbol
Table 10. DC characteristics
Parameter
Test conditions (in addition to
those in Table 7 and Table 8)
Min.
Max. Unit
I_LI
Input leakage current
(SCL, SDA, E2, E1, E0)
V_IN = V_SS or V_CC,
device in Standby mode
-
±2
µA
I_LO
Output leakage current
SDA in Hi-Z, external voltage
applied on SDA: V_SS or V_CC
-
±2
µA
f_C = 400 kHz, V_CC = 5.5 V
-
2
mA
f_C = 400 kHz, V_CC = 2.5 V
-
2
mA
I_CC Supply current (Read)
f_C = 400 kHz, V_CC = 1.8 V
f_C = 1 MHz, V_CC = 5.5 V
-
1
mA
-
2
mA
f_C = 1 MHz, V_CC = 2.5 V
-
2
mA
f_C = 1 MHz, V_CC = 1.8 V
-
2
mA
I_CC0 Supply current (Write)
I_CC1 Standby supply current
During t_W
-
Device not selected⁽¹⁾, t° = 85 °C,
V_IN = V_SS or V_CC, V_CC = 1.8 V
-
Device not selected⁽¹⁾, t° = 85 °C
V_IN = V_SS or V_CC, V_CC = 2.5 V
-
Device not selected⁽¹⁾, t° = 85 °C,
V_IN = V_SS or V_CC, V_CC = 5.5 V
-
Device not selected⁽¹⁾, t° = 125 °C,
V_IN = V_SS or V_CC, V_CC = 1.8 V
-
Device not selected⁽¹⁾, t° = 125 °C,
V_IN = V_SS or V_CC, V_CC = 2.5 V
-
Device not selected⁽¹⁾, t° = 125 °C,
V_IN = V_SS or V_CC, V_CC = 5.5 V
-
2
mA
1
µA
2
µA
3
µA
15
µA
15
µA
20
µA
V_IL
Input low voltage (SCL, SDA, WC) -
–0.45 0.3 V_CC V
Input high voltage (SCL, SDA)
-
V_IH
Input high voltage (WC, E2, E1, E0) -
0.7 V_CC
6.5
V
0.7 V_CC V_CC +0.6 V
V_OL Output low voltage
V_RES ⁽²⁾ Internal reset threshold voltage
I_OL = 2.1 mA, V_CC = 2.5 V or
I_OL = 3 mA, V_CC = 5.5 V
I_OL = 1 mA, V_CC = 1.8 V
-
-
0.4
V
-
0.3
V
0.5
1.5
V
1. The device is not selected after power-up, after a Read instruction (after the Stop condition), or after the completion of the
internal write cycle t_W (t_W is triggered by the correct decoding of a Write instruction).
2. Characterized only, not 100% tested.
28/40
DocID023507 Rev 5