STM32F358XC Datasheet, PDF (1/134 Pages) STMicroelectronics – Operating conditions

STM32F358xC
ARM^®-based Cortex^®-M4 32b MCU+FPU, up to 256KB Flash+
48KB SRAM, 4 ADCs, 2 DAC ch., 7 comp., 4 PGA, timers, 1.8 V
Datasheet - production data
Features
• Core: ARM^® Cortex^®-M4 32-bit CPU with FPU
(72 MHz max), single-cycle multiplication and
HW division, 90 DMIPS (from CCM), DSP
instruction and MPU (memory protection unit).
• Operating conditions:
– VDD: 1.8V +/- 8%
– VDDA voltage range: 1.65 to 3.6 V
• Memories
– 256 Kbytes of Flash memory
– Up to 40 Kbytes of SRAM, with HW parity
check implemented on the first 16 Kbytes.
– Routine bootster: 8 Kbytes of SRAM on
instruction and data bus, with HW parity
check (CCM: Core Coupled Memory)
• CRC calculation unit
• Reset and supply management
– Low-power modes: Sleep, and Stop
– VBAT supply for RTC and backup registers
• Clock management
– 4 to 32 MHz crystal oscillator
– 32 kHz oscillator for RTC with calibration
– Internal 8 MHz RC with x 16 PLL option
– Internal 40 kHz oscillator
• Up to 86 fast I/Os
– All mappable on external interrupt vectors
– Several 5 V-tolerant
• Interconnect matrix
• 12-channel DMA controller
• Up to four ADC 0.20 µS (up to 38 channels)
with selectable resolution of 12/10/8/6 bits, 0 to
3.6 V conversion range, separate analog
supply from 1.8 to 3.6 V
• Up to two 12-bit DAC channels with analog
supply from 2.4 to 3.6 V
• Seven fast rail-to-rail analog comparators with
analog supply from 1.65 to 3.6 V
• Up to four operational amplifiers that can be
used in PGA mode, all terminal accessible with
analog supply from 2.4 to 3.6 V
LQFP48 (7 × 7 mm)
LQFP64 (10 × 10 mm)
LQFP100 (14 × 14 mm)
• Up to 24 capacitive sensing channels
supporting touchkey, linear and rotary touch
sensors
• Up to 13 timers
– One 32-bit timer and two 16-bit timers with
up to 4 IC/OC/PWM or pulse counter and
quadrature (incremental) encoder input
– Up to two 16-bit 6-channel advanced-
control timers, with up to 6 PWM channels,
deadtime generation and emergency stop
– One 16-bit timer with 2 IC/OCs, 1
OCN/PWM, deadtime generation and
emergency stop
– Two 16-bit timers with IC/OC/OCN/PWM,
deadtime generation and emergency stop
– 2 watchdog timers (independent, window)
– SysTick timer: 24-bit downcounter
– Up to two 16-bit basic timers to drive the
DAC
• Calendar RTC with Alarm, periodic wakeup
from Stop
• Communication interfaces
– CAN interface (2.0B Active)
– Two I2C Fast mode plus (1 Mbit/s) with 20
mA current sink, SMBus/PMBus, wakeup
from STOP
– Up to five USART/UARTs (ISO 7816
interface, LIN, IrDA, modem control)
– Up to three SPIs, two with multiplexed I2S
interface, 4 to 16 programmable bit frames
– Infrared Transmitter
• Cortex^®-M4 with FPU ETM, Serial wire debug,
JTAG
• 96-bit unique ID
Table 1. Device summary
Reference
Part number
STM32F358xC STM32F358CC, STM32F358RC, STM32F358VC
April 2015
This is information on a product in full production.
DocID025540 Rev 4
1/134
www.st.com