T00014D_15 Datasheet, PDF (2/2 Pages) Solid States Devices, Inc – HIGH VOLTAGE BIDIRECTIONAL TRANSIENT VOLTAGE SUPPRESSOR

Solid State Devices, Inc.
14701 Firestone Blvd, La Mirada, Ca 90638
Phone: [phone]
Fax: [phone]
[e-mail]
www.ssdi-power.com
STA60K79S thru
STA60K1000S
ELECTRICAL CHARACTERISTICS (note 2)
Break Down (note 1) Max Reverse Stand Off
Part
Number
(note 4)
Nominal
Voltage
Test
Current
Voltage
Reverse
Leakage
Current
V_BR
@ I_BRT
V_RWM
I_R@V_RWM
Peak Pulse Clamping
@ Current
Voltage
tp=1ms
(Max)
(note 3)
V_C
I_PP
Maximum
Continuous
Current
I_RM
Max
Temperature
Coefficient
T_C
Volts
mA
Volts
µA
Volts
Amps
Amps
%/°C
STA60K79S
79
700
56
6000
145
512
5.00
.03
STA60K89S
89
600
62
4800
150
480
4.60
.03
STA60K98S
98
600
68
160
160
436
4.08
.03
STA60K107S
107
500
75
80
175
400
3.80
.05
STA60K110S
110
500
82
60
185
372
3.44
.05
STA60K127S
127
400
91
40
195
348
3.08
.05
STA60K135S
135
400
100
16
210
316
2.80
.05
STA60K150S
150
300
110
8
230
272
2.40
.05
STA60K167S
167
300
120
8
250
256
2.20
.06
STA60K180S
180
260
130
8
270
228
2.00
.06
STA60K202S
202
260
150
8
300
208
1.76
.06
STA60K226S
226
200
160
8
335
188
1.56
.06
STA60K245S
245
200
180
8
360
172
1.44
.06
STA60K279S
279
200
200
8
400
156
1.24
.06
STA60K305S
305
160
220
8
435
140
1.12
.06
STA60K340S
340
160
240
8
470
128
1.04
.06
STA60K360S
360
120
270
8
520
120
0.96
.06
STA60K390S
390
120
300
8
550
108
0.84
.06
STA60K450S
450
120
330
8
600
100
0.72
.07
STA60K490S
490
100
360
8
650
92
0.70
.07
STA60K510S
510
100
390
8
700
84
0.68
.07
STA60K560S
560
80
430
8
780
76
0.64
.07
STA60K620S
620
80
470
8
870
68
0.60
.08
STA60K680S
680
80
510
8
930
64
0.52
.08
STA60K750S
750
80
560
8
1033
56
0.48
.08
STA60K820S
820
60
620
8
1135
52
0.44
.08
STA60K910S
910
60
680
8
1265
48
0.40
.08
STA60K1000S 1000
48
750
8
1385
44
0.36
.09
PEAK PULSE POWER VS. PULSE WIDTH
CURRENT PULSE WAVEFORM
STEADY STATE POWER DERATING
PULSE WIDTH
CASE TEMPERATURE (°C)
For optional high reliability screening or higher zener voltages, consult SSDI MARKETING Department.
Notes:
1. All voltages are measured with automated test set using 35 msec test time. Longer or shorter test times will have a corresponding effect on the measured value
due to heating effects.
2. Unless specified otherwise, ratings based on 25° C case temperature.
3. Pulse width (tp) is defined as the time from rated peak pulse current IPP to the point where peak pulse current decayed to 50% of rated IPP.
(10µs X 1000µs waveform as defined by R.E.A.)
4. Part Number- For 5% Voltage Tolerance, specify “B” in place of “A”
NOTE: All specifications are subject to change without notification.
SCD's for these devices should be reviewed by SSDI prior to release.
DATA SHEET #: T00014D
DOC