T00008 Datasheet, PDF (2/2 Pages) Solid States Devices, Inc – LOW VOLTAGE BIDIRECTIONAL TRANSIENT VOLTAGE SUPPRESSOR

STA60K7.9P
thru
STA60K100P
Electrical Characteristics
Part
Number
For 5% Voltage
Tolerance specify
"B" in place of A
STA60K7.9P
STA60K8.9P
STA60K9.8P
STA60K10.7P
STA60K11P
STA60K12.7P
STA60K13.5P
STA60K15P
STA60K16.7P
STA60K18P
STA60K20.2P
STA60K22.6P
STA60K24.5P
STA60K27.9P
STA60K30.5P
STA60K34P
STA60K36P
STA60K39P
STA60K45P
STA60K49P
STA60K51P
STA60K57P
STA60K62P
STA60K68P
STA60K75P
STA60K82P
STA60K91P
STA60K100P
Break Down (note 1)
Nominal
Test
Voltage Current
V_BR
@I_BRT
Volts
A
7.9
7.0
8.9
6.0
9.8
6.0
10.7
5.0
11.0
5.0
12.7
4.0
13.5
4.0
15.0
3.0
16.7
3.0
18.0
2.6
20.2
2.6
22.6
2.0
24.5
2.0
27.9
2.0
30.5
1.6
34.0
1.6
36.0
1.2
39.0
1.2
45.0
1.2
49.0
1.0
51.0
1.0
57.0
0.8
62.0
0.8
68.0
0.8
75.0
0.8
82.0
0.6
91.0
0.6
100.0
0.6
SOLID STATE DEVICES, INC.
14830 Valley View Blvd * La Mirada, Ca 90638
Phone: [phone] * Fax: [phone]
Max Reverse Stand Off
Voltage
V_RWM
Reverse
Leakage
Current
I_R @ V_RWM
Volts
mA
Peak Pulse Clamping
Voltage
(max)
V_C
@ Current
tp=1ms
(note 4)
I_PP
Volts
A
5.6
60
14.5
5120
6.2
48
15.0
4800
6.8
1.6
16.0
4360
7.5
0.8
17.5
4000
8.2
0.8
18.5
3720
9.1
0.8
19.5
3480
10
0.8
21.0
3160
11
0.8
23.0
2720
12
0.8
25.0
2560
13
0.8
27.0
2280
15
0.8
30.0
2080
16
0.8
33.5
1880
18
0.8
36.0
1720
20
0.8
40.0
1560
22
0.8
43.5
1400
24
0.8
47.0
1280
27
0.8
52.0
1200
30
0.8
55.0
1080
33
0.8
60.0
1000
36
0.8
65.0
920
39
0.8
70.0
840
43
0.8
78.0
760
47
0.8
87.0
680
51
0.8
93.0
640
56
0.8
103.3
560
62
0.8
113.5
520
68
0.8
126.5
480
75
0.8
138.5
440
Maximum
Continuous
Current
(note 3)
I_RM
A
28
30
33
38
43
45
48
48
48
50
63
70
75
95
125
175
200
175
250
300
350
450
500
550
625
750
1000
1125
Dynamic
Impedance
(note 2)
Maximum
Termperature
Coefficient
Z_BR @ I_BRT
TC
Ohms % / °C
0.07
.03
0.08
.03
0.09
.03
0.10
.05
0.11
.05
0.11
.05
0.12
.05
0.12
.05
0.13
.06
0.13
.06
0.15
.06
0.16
.06
0.18
.06
0.25
.06
0.40
.06
0.50
.06
0.60
.06
0.70
.06
1.0
.06
1.2
.07
1.4
.07
1.8
.07
2.0
.07
2.2
.08
2.5
.08
3.0
.08
4.0
.08
4.5
.09
PEAK PULSE POWER VS. PULSE WIDTH
CURRENT PULSE WAVEFORM
STEADY STATE POWER DERATING
PULSE WIDTH
CASE TEMPERATURE (°C)
For optional high reliability screening or higher zener voltages, consult SSDI MARKETING Department.
Notes:
1. All voltages are measured with automated test set using 35 msec test time. Longer or shorter test times will have a corresponding effect on the measured
value due to heating effects.
2. Dynamic impedance is derived from the AC voltage divided by the AC current with RMS value of 10% of DC test current superimposed on the test
current.
3. Ratings based on 25° C case temperature.
4 . Pulse width (tp) is delined as the time from rated peak pulse current IPP to the point where peak pulse current decayed to 50% of rated IPP.