T00006 Datasheet, PDF (2/2 Pages) Solid States Devices, Inc – UNIDIRECTIONAL TRANSIENT VOLTAGE SUPPRESSOR

Solid State Devices, Inc.
14701 Firestone Blvd, La Mirada, Ca 90638
Phone: [phone]
Fax: [phone]
[e-mail]
www.ssdi-power.com
STA15K7.5P thru
STA15K100P
ELECTRICAL CHARACTERISTICS
Break Down (note 1) Max Reverse Stand Off
Part
Number
(note 5)
Nominal
Voltage
Test
Current
Voltage
Reverse
Leakage
Current
V_{B R}
@ I_BRT
V_RWM
I_R@V_RWM
Peak Pulse Clamping
Voltage
(Max)
@ Current
Tp=1ms
(note 4)
V_C
I_PP
Maximum
Continuous
Current
(note 4)
I_RM
Dynamic
Impedance
(note 2)
Z_BR@I_BRT
Max
Temperat
ure
Coefficient
T_C
Volts
Amps
Volts
mA
Volts
Amps
Amps
Ohms
% /°C
STA15K7.5P
7.5
1.75
5.6
STA15K8.2P
8.2
1.50
6.2
STA15K9.1P
9.1
1.50
6.8
STA15K10P
10
1.25
7.5
STA15K11P
11
1.25
8.2
15.0
11.7
1280
12.0
12.5
1200
0.40
13.8
1090
0.20
15.0
1000
0.15
16.2
930
12.5
0.07
.03
11.5
0.08
.03
10.2
0.09
.03
9.5
0.10
.05
8.6
0.11
.05
STA15K12P
12
STA15K13P
13
STA15K15P
15
STA15K16P
16
STA15K18P
18
1.00
9.1
1.00
10
0.75
11
0.75
12
0.65
13
0.10
17.3
870
0.04
19.0
790
0.02
22.0
680
0.02
23.5
640
0.02
26.5
570
7.7
0.11
.05
7.0
0.12
.05
6.0
0.12
.05
5.5
0.13
.06
5.0
0.13
.06
STA15K20P
20
STA15K22P
22
STA15K24P
24
STA15K27P
27
STA15K30P
30
0.65
15
0.50
16
0.50
18
0.50
20
0.40
22
0.02
29.0
520
0.02
31.9
470
0.02
34.7
430
0.02
38.5
390
0.02
42.9
350
4.4
0.15
.06
3.9
0.16
.06
3.6
0.18
.06
3.1
0.25
.06
2.8
0.40
.06
STA15K33P
33
STA15K36P
36
STA15K39P
39
STA15K43P
43
STA15K47P
47
0.40
24
0.30
27
0.30
30
0.30
33
0.25
36
0.02
46.9
320
0.02
50.0
300
0.02
55.6
270
0.02
60.0
250
0.02
65.2
230
2.6
0.50
.06
2.4
0.60
.06
2.1
0.70
.06
1.8
1.0
.06
1.75
1.2
.07
STA15K51P
51
STA15K56P
56
STA15K62P
62
STA15K68P
68
STA15K75P
75
0.25
39
0.20
43
0.20
47
0.20
51
0.20
56
0.02
71.4
210
0.02
78.9
190
0.02
88.2
170
0.02
93.7
160
0.02
107.1
140
1.7
1.4
.07
1.6
1.8
.07
1.5
2.0
.07
1.3
2.2
.08
1.2
2.5
.08
STA15K82P
82
0.15
62
STA15K91P
91
0.15
68
STA15K100P 100
0.15
75
0.02
115.4
130
0.02
125.0
120
0.02
136.4
110
1.1
3.0
.08
1.0
4.0
.08
.9
4.5
.09
PEAK PULSE POWER VS. PULSE WIDTH
CURRENT PULSE WAVEFORM
STEADY STATE POWER DERATING
PULSE WIDTH
CASE TEMPERATURE (°C)
For optional high reliability screening or higher zener voltages, consult SSDI MARKETING Department.
Notes:
1. All voltages are measured with automated test set using 35 msec test time. Longer or shorter test times will have a corresponding effect on the measured value
due to heating effects.
2. Dynamic impedance is derived from the AC voltage divided by the AC current with RMS value of 10% of DC test current superimposed on the test current.
3. Ratings based on 25° C case temperature.
4. Pulse width (tp) is delined as the time from rated peak pulse current IPP to the point where peak pulse current decayed to 50% of rated IPP.
(10ms X 1000ms waveform as defined by R.E.A.)
5. Part Number- For 5% Voltage Tolerance, sp ecify “B” in place of “A”