LAN9514_12 Datasheet, PDF (11/52 Pages) SMSC Corporation – USB 2.0 Hub and 10/100 Ethernet Controller

USB 2.0 Hub and 10/100 Ethernet Controller
Datasheet
NUM
PINS
NAME
Ethernet Link
Activity Indicator
LED
1
General
Purpose I/O 1
Ethernet Speed
Indicator LED
1
General
Purpose I/O 2
General
1
Purpose I/O 3
General
1
Purpose I/O 4
General
1
Purpose I/O 5
General
1
Purpose I/O 6
General
1
Purpose I/O 7
Detect
Upstream
VBUS Power
1
Auto-MDIX
1
Enable
Table 2.3 Miscellaneous Pins (continued)
SYMBOL
nLNKA_LED
GPIO1
nSPD_LED
BUFFER
TYPE
DESCRIPTION
OD12
(PU)
This pin is driven low (LED on) when a valid link is
detected. This pin is pulsed high (LED off) for
80mS whenever transmit or receive activity is
detected. This pin is then driven low again for a
minimum of 80mS, after which time it will repeat
the process if TX or RX activity is detected.
Effectively, LED2 is activated solid for a link. When
transmit or receive activity is sensed, LED2 will
function as an activity indicator.
IS/O12/
OD12
(PU)
This General Purpose I/O pin is fully programmable
as either a push-pull output, an open-drain output,
or a Schmitt-triggered input.
OD12
(PU)
This pin is driven low (LED on) when the Ethernet
operating speed is 100Mbs, or during auto-
negotiation. This pin is driven high during 10Mbs
operation, or during line isolation.
GPIO2
GPIO3
GPIO4
GPIO5
GPIO6
GPIO7
VBUS_DET
AUTOMDIX_EN
IS/O12/
OD12
(PU)
IS/O8/
OD8
(PU)
IS/O8/
OD8
(PU)
IS/O8/
OD8
(PU)
IS/O8/
OD8
(PU)
IS/O8/
OD8
(PU)
IS_5V
IS
This General Purpose I/O pin is fully programmable
as either a push-pull output, an open-drain output,
or a Schmitt-triggered input.
This General Purpose I/O pin is fully programmable
as either a push-pull output, an open-drain output,
or a Schmitt-triggered input.
This General Purpose I/O pin is fully programmable
as either a push-pull output, an open-drain output,
or a Schmitt-triggered input.
This General Purpose I/O pin is fully programmable
as either a push-pull output, an open-drain output,
or a Schmitt-triggered input.
This General Purpose I/O pin is fully programmable
as either a push-pull output, an open-drain output,
or a Schmitt-triggered input.
This General Purpose I/O pin is fully programmable
as either a push-pull output, an open-drain output,
or a Schmitt-triggered input.
This pin detects the state of the upstream bus
power. The Hub monitors VBUS_DET to determine
when to assert the USBDP0 pin's internal pull-up
resistor (signaling a connect event).
For bus powered hubs, this pin must be tied to
VDD33IO.
For self powered hubs where the device is
permanently attached to a host, VBUS_DET should
be pulled to VDD33IO. For other self powered
applications, refer to the device reference
schematic for additional connection information.
Determines the default Auto-MDIX setting.
0 = Auto-MDIX is disabled.
1 = Auto-MDIX is enabled.
SMSC LAN9514/LAN9514i
11
DATASHEET
Revision 1.2 (02-29-12)