SPF-500 Datasheet, PDF (1/2 Pages) SL Power Electronics – 500-1000 Watts Single Output, Forced Current Sharing

SPF-500, SPF-750, SPF-1000 Commercial Series
500-1000 Watts Single Output, Forced Current Sharing
FEATURES:
• Forced current sharing for N +1 redundancy
• Universal ac input
• 0.99 typical power factor
• Low ripple and noise
• Dc power good and ac power fail signals
• True remote inhibit
• Monotonic turn-on and turn-off
SPECIFICATIONS:
INPUT
Ac Input: 90-264 Vac continuous range, 47 to 63 Hz. 750 W
units fused for 15 A. 1000 W units fused for 20 A.
Power Factor: 0.99 typical at full load. Meets EN61000-3-2 Class A.
Inrush: Cold start ac current is less than 50 A at 115 Vac and
100 A at 230 Vac for 500 W and 750 W models; 90 A at 115 Vac
and 180 A at 230 Vac for 1000 W models. Limited by thermistor.
Brownout Protection: Continuous range units hold regulation to
85 Vac.
Holdup Time: 20 ms minimum after removal of power at full load.
Efficiency: 75% typical.
Ac Power Fail: Provides TTL “0” 5 ms before output voltage
goes out of regulation band upon loss of power.
OUTPUT
Adjustability: User adjustable ±5% minimum.
Line & Load Reg: ±1% over ac input range and 0 to 100% load
change.
Ripple & Noise: Less than 1% p-p or 100 mV, whichever is
greater.
Remote Sense: Compensates for 250 mV total line drop. Open
sense lead protection. (See Redundancy, below.)
Temperature Coefficient: 0.02% per degree C.
Stability: 0.1% over 8 hours after 30 minutes warm-up.
Transient Response: Output voltage returns to within 1% in less
than 500 µs for a 50% load change. Peak transient does not
exceed 5%.
Overload Protection: All outputs are protected against overload
and short circuit. Automatic recovery upon removal of fault.
Overvoltage Protection: Protects load against power supply
induced overvoltage. Trip point is factory set so that output
voltage cannot exceed 136% of nominal.
Remote Inhibit: Contact closure to the negative sense line or a
TTL level “0” turns off dc output.
Dc Power Good (5 V Outputs): Provides a TTL “1” open
collector when output is above 4.6 V nominal.
Redundancy: External OR-ing diodes and forced current
sharing provide “N+1” capability. Remote sense (+S) compen-
sates for additional 0.6 V diode voltage drop. When the current
sharing terminal is connected between units, current sharing
remains within 10% of the unit’s full output current rating.
Reverse Voltage: Protected against reverse voltage up to supply
current rating.
ENVIRONMENTAL
Thermal Protection: Shuts down power supply if overheated.
Automatic recovery.
Temperature Range: 0° to 50°C at full ratings.
Safety Agencies: Most models are approved to UL1950; CSA
22.2 #234; IEC 950 and TÜV EN60950, Class 1 SELV., CE 72/23/
EEC/93/68EEC (low voltage directive).
Conducted RFI: Meets FCC Part 15, Class A; EN55022 Class B.
Output Isolation: Isolated from ground 50 Vdc.
Cooling: Self cooled by internal ball-bearing fans.
OPTIONS:
Consult factory for available options.
AC INPUT (90-264 VAC Continuous Range)
FUNCTION
115 VAC*
230 VAC
CONNECTOR
TB1-(L)
Line
Line 1
Barrier strip
TB1-(N)
Neutral
Line 2
#6-32 screws 3/8 centers
TB1-(GND) Safety Ground
Safety Ground
DC OUTPUT
FUNCTION
MODEL
LOCATION
CONNECTOR
Output
All SPF-500 models Terminal +V Bus bars #8-32 screws 2PL
Terminal -V
Voltage
All SPF-750 models Terminal +V Bus bars #1/4-20 screws 2PL
Terminal -V
SPF-1000-24,28,36,48 Terminal +V Bus bars #10-32 screws 2PL
Terminal -V
STATUS AND CONTROL
FUNCTION
SPF-500 SPF-750
SPF-1000
CONNECTOR
Remote Sense J1-2 (S+) J1-5 (S+) J3-7 (S+) AMP MTA TYPE
J1-1 (S-) J1-4 (S-) J3-8 (S-)
#640456-6 (J1-500W)
Power Good
J1-7
J1-3
J3-5
or #640656-3 (J2-500W)
Inhibit
J1-5
J1-2
J3-4
Current Share J1-6
J1-6
J3-6
Ac Power Fail J1-8
J1-1
J3-3
or #640656-6 (J1-750W)
or #640456-8 (J3-
1000W)
pin headers (locking)
Aux. Fan Voltage J2-1 (+12V) N/A
J3-1 (+12V)
J2-2 (Rtn) N/A
J3-2 (RTN)
Signal Ground J1-10
N/A
N/A
Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033
86
800-235-5929 • 805-486-4565 • FAX [phone] • www.condorpower.com