SKY73013-306 Datasheet, PDF (4/7 Pages) Skyworks Solutions Inc. – Direct Quadrature Demodulator 4.9-5.925 GHz Featuring No-Pull LO Architecture

PRELIMINARY DATA SHEET • SKY73013-306
Pin Out
Gain
EN C I- I+
16 15 14 13
R_BIAS 1
12 N/C
LNA+ 2
11 LO-
LNA- 3
10 LO+
GND 4
9 CTR2
5678
V_CC Q+ Q- CTR
Evaluation Board
The SKY73013 Evaluation Board is used to test the performance
of the SKY73013 Direct Quadrature Demodulator. The evaluation
board BOM is as shown in the table below.
The evaluation board for SKY73013 allows the part to be fully
exercised. The board is populated with several components
which are not required for normal operation but facilitate special
testing of the SKY73013, such as two high gain, differential
baseband amplifiers which are well-suited for differential-to-
single-ended conversion, and are included for noise figure
measurements.
The evaluation board requires a power supply voltage of 3.3 V
nominal, that is capable of sourcing 50 mA.
Evaluation Circuit PCB
V_CC
VGC (LNA On/Off)
IF Outputs:
[I-, I+, Q+, Q-]
RF+
RF-
Op-Amp Power Header
[+5 V, +1.5 V, GND, -5 V]
LO+
LO-
Op-Amp
IF Outputs:
[I-, I+, Q+, Q-]
High Gain Op-Amps to
Observe very Small
Signals on an Oscilloscope
Pin Descriptions
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Name
R_BIAS
LNA+
LNA1
GND
V_CC
Q+
Q-
CTR1
CTR2
LO+
LO-
N/C
I+
I-
GainC
16
EN
Paddle
Description
Bias resistor. Nominal value = 1.2 k, 1%
RF input +
RF input -
Ground
Supply voltage
BB/IF Q+ output
BB/IF Q- output
Debug pin; connect to ground
Debug pin; connect to ground
Local oscillator input +
Local oscillator input -
No connection
BB/IF I+ output
BB/IF I- output
Gain control; LNA is ON with V_CC applied to
this pin, off when grounded
Chip enable; chip is enabled with V_CC applied
to this pin and disabled when this pin is
grounded
Must be connected via lowest possible
impedance to ground for proper electrical
and thermal performance
Absolute Maximum Ratings
Characteristic
Value
RF Input Power
0 dBm
Supply voltage
4.5 V
Supply current
60 mA
LO input power
0 dBm
Operating temperature
-40 °C to +85 °C
Storage temperature
-65 °C to +85 °C
Performance is guaranteed only under the conditions listed in the specifications table and is
not guaranteed under the full range(s) described by the Absolute Maximum specifications.
Exceeding any of the absolute maximum/minimum specifications may result in permanent
damage to the device and will void the warranty.
CAUTION: Although this device is designed to be as robust as
possible, ESD (Electrostatic Discharge) can damage
this device. This device must be protected at all times
from ESD. Static charges may easily produce poten-
tials of several kilovolts on the human body or
equipment, which can discharge without detection.
Industry-standard ESD precautions must be employed
at all times.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
4
August 18, 2006 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 200508 Rev. B