SKY13296-340LF Datasheet, PDF (4/6 Pages) Skyworks Solutions Inc. – GaAs SP4T Absorptive Switch 20 MHz–2.5 GHz

DATA SHEET • SKY13296-340LF
Pin Out
(Top View X-ray of Pads on Bottom of Package)
J₄ 1
GND 4 2
GND 3 3
J₃ ⁴
GND 5
20 19 18 17 16
15 J₁
14 _{GND 1}
13 GND 2
12 _J2
11 V_CTL1
6 7 8 9 10
DC blocks are required on RFc, J₁, J₂, J₃, J₄.
Floating caps are required on Gnd 1, Gnd 2, Gnd 3, Gnd 4.
Truth Table
V_DD
V_{CTL 1} V_{CTL 2} RFc-J₁
1
0
0 Ins. Loss
1
1
0
Isolation
1
0
1
Isolation
1
1
1
Isolation
V_DD must be powered on prior to a VCTL hgih signal.
“0” = 0 to 0.2 V.
“1” = 2.75 to V_DD V.
V_DD = 3 V to 5 V.
RFc-J₂
Isolation
Ins. Loss
Isolation
Isolation
RFc-J₃
Isolation
Isolation
Ins. Loss
Isolation
RFc-J₄
Isolation
Isolation
Isolation
Ins. Loss
Absolute Maximum Ratings
Characteristic
Value
V_DD voltage range
RF input power @ 5.5 V
2.75 < V_DD < 5.5 V
1 W, f > 500 MHz
Operating temperature
-40 °C to +85 °C
Storage temperature
-65 °C to +150 °C
Performance is guaranteed only under the conditions listed in the specifications table and is
not guaranteed under the full range(s) described by the Absolute Maximum specifications.
Exceeding any of the absolute maximum/minimum specifications may result in permanent
damage to the device and will void the warranty.
CAUTION: Although this device is designed to be as robust as
possible, ESD (Electrostatic Discharge) can damage
this device. This device must be protected at all times
from ESD. Static charges may easily produce poten-
tials of several kilovolts on the human body or
equipment, which can discharge without detection.
Industry-standard ESD precautions must be employed
at all times.
Pin Assignments
Pin
Symbol
1 J₄
2 GND 4
3 GND 3
4 J₃
5 GND
6 V_DD
7 GND
8 GND
9 GND
11 V_{CTL 1}
10 V_{CTL 2}
12 J₂
13 GND 2
14 GND 1
15 J₁
16 GND
17 GND
18 RFc
19 GND
20 GND
Exposed
Paddle
Description
RF port. Must be DC blocked with a capacitor
appropriate for lowest frequency of operation
AC Ground for J₄ RF port. Must be DC blocked using
a capacitor appropriate for lowest frequency of
desired input return loss on J₄ port
AC Ground for J₃ RF port. Must be DC blocked using
a capacitor appropriate for lowest frequency of
desired input return loss on J₃ port
RF port. Must be DC blocked with a capacitor
appropriate for lowest frequency of operation
DC Ground
Supply voltage for decoder
DC Ground
DC Ground
DC Ground
DC control voltage applied to decoder
DC control voltage applied to decoder
RF port. Must be DC blocked with a capacitor
appropriate for lowest frequency of operation
AC Ground for J₂ RF port. Must be DC blocked using
a capacitor appropriate for lowest frequency of
desired input return loss on J₂ port
AC Ground for J₁ RF port. Must be DC blocked using
a capacitor appropriate for lowest frequency of
desired input return loss on J₁ port
RF port. Must be DC blocked with a capacitor
appropriate for lowest frequency of operation
DC Ground
DC Ground
RF common port. Must be DC blocked with a
capacitor appropriate for lowest frequency
of operation
DC Ground
DC Ground
DC Ground
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
4
September 18, 2007 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 200613 Rev. B