SP6132 Datasheet, PDF (5/14 Pages) Sipex Corporation – Wide Input, 300KHz Synchronous PWM Controller

tection features include thermal shutdown and
short-circuit detection. In the event that either a
thermal, short-circuit, or UVLO fault is de-
tected, the SP6132 is forced into an idle state
where the output drivers are held off for a finite
period before a re-start is attempted.
Soft Start
“Soft Start” is achieved when a power converter
ramps up the output voltage while controlling
the magnitude of the input supply source cur-
rent. In a modern step down converter, ramping
up the positive terminal of the error amplifier
controls soft start. As a result, excess source
current can be defined as the current required to
charge the output capacitor.
IV_IN = C_OUT * DV_OUT / DTSoft-start
The SP6132 provides the user with the option to
program the soft start rate by tying a capacitor
from the SS pin to GND. The selection of this
capacitor is based on the 10uA pull up current
present at the SS pin and the 0.8V reference
voltage. Therefore, the excess source can be
redefined as:
IV_IN = C_OUT * DV_OUT *10µA / (C_SS * 0.8V)
Under Voltage Lock Out (UVLO)
The SP6132 contains two separate UVLO com-
parators to monitor the bias (V_CC) and conver-
sion (V_IN) voltages independently. The V_CC
UVLO threshold is internally set to 4.25V,
whereas the V_IN UVLO threshold is program-
mable through the UVIN pin. When the UVIN
pin is greater than 2.5V, the SP6132 is permitted
to start up pending the removal of all other
faults. Both the V_CC and V_IN UVLO compara-
tors have been designed with hysteresis to pre-
vent noise from resetting a fault.
THEORY OF OPERATION: Continued
Thermal and Short-Circuit
Protection
Because the SP6132 is designed to drive large
NFETs running at high current, there is a chance
that either the controller or power converter will
become too hot. Therefore, an internal thermal
shutdown (145°C) has been included to prevent
the IC from malfunctioning at extreme tempera-
tures.
A short-circuit detection comparator has also
been included in the SP6132 to protect against
the accidental short or sever build up of current
at the output of the power converter. This com-
parator constantly monitors the positive and
negative terminals of the error amplifier, and if
the V_FB pin ever falls more than 250mV (typi-
cal) below the positive reference, a short-circuit
fault is set. Because the SS pin overrides the
internal 0.8V reference during soft start, the
SP6132 is capable of detecting short-circuit
faults throughout the duration of soft start as
well as in regular operation.
Handling of Faults:
Upon the detection of power (UVLO), thermal,
or short-circuit faults, the SP6132 is forced into
an idle state where the SS and COMP pins are
pulled low and the gate drivers are held off. In
the event of UVLO fault, the SP6132 remains in
this idle state until the UVLO fault is removed.
Upon the detection of a thermal or shor-circuit
fault, an internal 200ms (typical) timer is acti-
vated. In the event of a short-circuit fault, a re-
start is attempted immediately after the 200ms
timeout expires. Wereas, when a thermal fault
is detected the 200ms delay continuously re-
cycles and a re-start cannot be attempted until
the thermal fault is removed and the timer ex-
pires.
Error Amplifier and Voltage Loop
As stated before, the heart of the SP6132 voltage
error loop is a high performance, wide band-
width transconductance amplifier. Because of
the amplifier’s current limited (+/-150µA)
Date: 8/4/04
SP6132 Wide Input, 300KHz Synchronous PWM Controller
5
© Copyright 2004 Sipex Corporation