SP42742 Datasheet, PDF (3/10 Pages) SIPAT Co,Ltd – 75  Terminated, 5 - 2200 MHz SPDT

SP42742
Product Specification
Figure 3. Pin Configuration (Top View)
GND 1
GND 2
RF1 3
GND 4
GND 5
GND
75
75
15 GND
14 GND
13 RF2
12 GND
11 GND
Table 3. Pin Descriptions
No.
Name
Description
1, 2, 4-7, 9-12,
14, 15, 18, 19
3
GND
RF1¹
RF Ground
RF I/O
8
RFC¹
RF Common
13
RF2¹
RF I/O
16
C2²
Control 2 (or logic select)
17
C1²
Control 1 (or logic select)
20
VDD
Supply
Pad
GND
RF Ground Pad
Notes:
1. RF pins 3, 8, and 13 must be at 0 VDC. The RF pins do
not require DC blocking capacitors for proper operation if the
0 V DC requirement is met.
2. Pins 16 and 17 can be set for single pin or complementary
pin control.
Table 4. Moisture Sensitivity Level
and Fabrication Plant
The SP42742 in the 20-lead QFN package is rated
MSL1. Please note the difference in fabrication plants
for the following ordering codes.
Ordering Code
SP42742MLIBB
Moisture Sensitivity Level
MSL1
Fabrication
Plant
2
SP42742MLIBB-Z
MSL1
2
SP42742MLIBA
MSL1
2
SP42742MLIBA-Z
MSL1
2
42742-51
42742-52
MSL1
1
MSL1
1
Table 5. Operating Conditions @ 25 °C
Parameter
V_DD Power Supply
Min
Typ Max Unit
2.7
3.0
3.3
V
I_DD Power Supply Current
(V_DD = 3 V, V_CNTL = 3 V)
8
µA
Control Voltage High
Control Voltage Low
0.7 x V_DD
0
V_DD
V
0.3 x V_DD V
Table 6. Absolute Maximum Ratings
Symbol Parameter/Condition Min Max Unit
V_DD
V_I
P_RF
T_ST
T_OP
V_ESD
(note 1)
V_ESD
(note 2)
Power supply voltage
Voltage on any DC input
RF power on RFC, RF1, RF2
Terminated/Through
Storage temperature
Operating temperature
HBM³ ESD Voltage RF Pins
HBM³ ESD Voltage Digital Pins
MM ESD Voltage all pins
HBM³ ESD Voltage RF Pins
HBM³ ESD Voltage Digital Pins
MM ESD Voltage all pins
-0.3 4.0
V
-0.3
V_DD +
0.3
V
24/33 dBm
-65 +150 °C
-40 +85 °C
2000
500
100
V
3500
3500
150
Notes:
1. Fabrication plant 1 parts, see Table 4. Please contact
factory for fabrication plant details.
2. Fabrication plan 2 parts, see Table 4. Please contact
factory for fabrication plant details.
3. ML_STD 883 Method 3015.7
Exceeding absolute maximum ratings may cause
permanent damage. Operation should be restricted to
the limits in the Operating Ranges table. Operation
between operating range maximum and absolute
maximum for extended periods may reduce reliability.
Electrostatic Discharge (ESD) Precautions
When handling this CMOS device, observe the
same precautions that you would use with other ESD-
sensitive devices. Although this device contains
circuitry to protect it from damage due to ESD,
precautions should be taken to avoid exceeding the
rating specified.
Latch-Up Avoidance
Unlike conventional CMOS devices, CMOS
devices are immune to latch-up.
Switching Frequency
The SP42742 has a maximum 25 kHz switching rate.
Tel: [phone] Fax: [phone] www.sipatsaw.com / [e-mail]
Page 3 of 10