SI3016 Datasheet, PDF (6/50 Pages) List of Unclassifed Manufacturers – 3.3 V ENHANCED GLOBAL DIRECT ACCESS ARRANGEMENT

Si3016
Table 3. DC Characteristics
(T_A = 0 to 70 °C for K-Grade and –40 to 85 °C for B-Grade)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Input Leakage Current
I_L
–10
—
10
µA
Power Supply Current, Analog*
I_A
—
0.3
—
mA
*Note: This current is required from the integrated system-side interface to communicate with the Si3016 through the isolation
interface.
Table 4. AC Characteristics
(T_A = 0 to 70 °C for K-Grade and –40 to 85 °C for B-Grade; see Figure 6 on page 9)
Parameter
Symbol
Test Condition
Min
Typ Max Unit
Sample Rate
Transmit Frequency Response
Fs
Fs = F_PLL2/5120
7.2
— 11.025 KHz
Low –3 dBFS Corner
—
0
—
Hz
Receive Frequency Response
Low –3 dBFS Corner
—
5
—
Hz
Transmit Full Scale Level¹
Receive Full Scale Level^1,3
Dynamic Range^4,5,6
Dynamic Range^4,5,7
Dynamic Range^4,5,6
Transmit Total Harmonic Distortion^6,8
Transmit Total Harmonic Distortion^7,8
Receive Total Harmonic Distortion^7,8
Receive Total Harmonic Distortion^6,8
V_FS
FULL = 0 (–1 dBm)
—
FULL = 1 (+3.2 dBm)²
—
V_FS
FULL = 0 (–1 dBm)
—
FULL = 1 (+3.2 dBm)³
—
DR ACT=0, DCT=10 (FCC) —
I_L=100 mA
DR ACT=0, DCT=01 (Japan) —
I_L=20 mA
DR ACT=1, DCT=11(CTR21) —
I_L=60 mA
THD ACT=0, DCT=10 (FCC) —
I_L=100 mA
THD ACT=0, DCT=01 (Japan) —
I_L=20 mA
THD ACT=0, DCT=01 (Japan) —
I_L=20 mA
THD ACT=1, DCT=11 (CTR21) —
I_L=60 mA
1
1.58
1
1.58
82
83
84
–85
–76
–74
–82
— V_PEAK
— V_PEAK
— V_PEAK
— V_PEAK
—
dB
—
dB
—
dB
—
dB
—
dB
—
dB
—
dB
Dynamic Range (Caller ID mode)
DR_CID VIN = 1 kHz, –13 dBm
—
60
—
dB
Notes:
1. Measured at TIP and RING with 600 Ω termination at 1 kHz, as shown in Figure 1.
2. R2 should be changed to a 243 Ω resistor when the FULLSCALE bit (FULL) is set to 1 (Register 18, bit 7).
3. Receive full scale level will produce –0.9 dBFS at SDO.
4. DR = 20 x log |Vin| + 20 x log (RMS signal/RMS noise).
5. Measurement is 300 to 3400 Hz. Applies to both transmit and receive paths.
6. Vin = 1 kHz, –3 dBFS, Fs = 10300 Hz.
7. Vin = 1 KHz, –6 dBFS, Fs = 10300 Hz.
8. THD = 20 x log (RMS distortion/RMS signal).
9. The AOUT pin is an optional pin located on the integrated system-side module. V_D refers to the digital power supply of
the integrated system-side module.
6
Rev. 1.0