AN675 Datasheet, PDF (1/2 Pages) Silicon Laboratories – PRECISION32™ MCU DEVELOPMENT KIT QUICK-START GUIDE

A. Install Software
1
Navigate to the Precision32
2
software download website.
Click the large Download Button to
initiate the Precision32 web install.
3
Start the Installer and allow it to run in
the background. Advance to Step 4 while
the Precision32 Development Suite and
AppBuilder are being installed.
www.silabs.com/
32bit-software
B. Hardware Setup (Steps 1, 4, and 5 Only Apply to Enhanced Development Kits)
1
If Enhanced DK, connect the MCU card
2
and I/O card to the UDP Motherboard.
Connect the USB Debug Adapter
ribbon cable to the MCU card.
3
Connect the USB Debug Adapter to the
PC using the standard USB cable.
MCU card
I/O card
MCU card
EVALUATION BOARD/KIT IMPORTANT NOTICE
Silicon Laboratories Inc. and its affiliated companies ("Silicon Labs") provides the enclosed evaluation board/kit to the user ("User") under the following conditions:
This evaluation board/kit ("EVB/Kit") is intended for use for ENGINEERING DEVELOPMENT, TESTING, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not a finished
end-product fit for general consumer use. ANY OTHER USE, RESALE, OR REDISTRIBUTION FOR ANY OTHER PURPOSE IS STRICTLY PROHIBITED. This EVB/Kit is not intended to
be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end
products that incorporate such semiconductor components or circuit boards. As such, persons handling this EVB/Kit must have electronics training and observe good engineering practice
standards. As a prototype not available for commercial reasons, this EVB/Kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility,
restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.
Should this EVB/Kit not meet the specifications indicated in the User's Guide, the EVB/Kit may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING
WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SILICON LABS TO USER, IS USER'S SOLE REMEDY, AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED,
IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY, NONINFRINGEMENT, DESIGN, WORKMANSHIP, OR FITNESS FOR ANY PARTICULAR PUR-
POSE.
User assumes all responsibility and liability for proper and safe handling of the EVB/Kit. Further, User indemnifies Silicon Labs from all claims arising from User's handling or use of the
EVB/Kit. Due to the open construction of the EVB/Kit, it is User's responsibility to take any and all appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CON-
SEQUENTIAL DAMAGES.
Neither Silicon Labs nor User is obligated to perform any activities or conduct any business as a consequence of using the EVB/Kit, and neither party is entitled to any form of exclusivity
with respect to the EVB/Kit.
Silicon Labs assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the EVB/Kit. This notice contains important safety information
about temperatures and voltages. For additional environmental and/or safety information, please contact a Silicon Labs application engineer or visit www.silabs.com/support/quality.
No license is granted under any patent right or other intellectual property right of Silicon Labs covering or relating to any machine, process, or combination in which the EVB/Kit or any of its
components might be or are used.
User's use of this EVB/Kit is conditioned upon acceptance of the foregoing conditions. If User is unwilling to accept these conditions, User may request a refund and return the EVB/Kit to
Silicon Labs in its original condition, unopened, with the original packaging and all documentation to:
Mailing Address:
400 W. Cesar Chavez
Austin, TX 78701
Copyright © 2012 by Silicon Laboratories
Rev. 0.2 7/12
4 ^{If Enhanced DK, apply power to the UDP}
5 ^{If Enhanced DK, update the motherboard}
6
If Development Kit, apply power to the
Motherboard using 1 of 4 power options,
firmware using the UDP Motherboard
MCU Card using 1 of 2 power options.
then set power switch (S3) to the ON Position.
Firmware Update Utility.
14
1
2
3
2
Power Options
1: 9 V Universal Adapter (J20)
2: Standard USB (J16)
3: Mini USB (J1)
4: 6 V Battery Pack (J11)
www.silabs.com/udp
Power Options
1: Mini USB – For USB MCUs
2: 9 V Universal Adapter – For Non-USB
MCUs
Note: If Enhanced DK, the MCU Card is powered
from the motherboard.
C. Documentation
1
Download the User’s Guide for Each
Board in the Development Kit.
Where to Find Documentation
Data Sheet:
www.silabs.com/32bit-mcuChoose Product FamilyDocumentation tab
Reference Manual:
www.silabs.com/32bit-mcuChoose Product FamilyDocumentation tab
Hardware User's Guide:
www.silabs.com/32bit-mcuDesign ResourcesUnified Development Platform
OR www.silabs.com/udp
Application Notes:
www.silabs.com/32bit-mcuDesign ResourcesApplication Notes
Software Development Kit Documentation:
C:\Silabs\32bit\si32-{revision}\Documentation\si32Hal.chm
Quality Documents:
www.silabs.com/quality