M40E-032220RT0 Datasheet, PDF (6/8 Pages) SICK AG – MULTIPLE LIGHT BEAM SAFETY DEVICES

M40S-032200AR0, M40E-032220RT0 | M4000 Standard
MULTIPLE LIGHT BEAM SAFETY DEVICES
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
Number of beams
2
3
4
5
6
7
8
Beam separation S1
500 (19.69)
600 (23.62)
220 (8.66)
400 (15.75)
450 (17.72)
220 (8.66)
300 (11.81)
220 (8.66)
L1
643 (25.31)
743 (29.25)
583 (22.95)
943 (37.13)
1,043 (41.06)
803 (31.61)
1,043 (41.06)
1,023 (40.28)
1,243 (48.94)
1,462 (57.56)
1,682 (66.22)
L2
672 (26.46)
772 (30.39)
612 (24.09)
972 (38.27)
1,072 (42.20)
832 (32.76)
1,072 (42.20)
1,052 (41.42)
1,272 (50.08)
1,491 (58.70)
1,711 (67.36)
Connection diagram
M4000 Standard connected to UE10-3OS safety relay
+24 V
M4000S
Standard
BN 2 _{+24 V}
5 _Test
1
n.c.
3 _n.c.
4 _n.c.
6 _n.c.
BU 7 _GND
SH
FE
M4000R
Standard
+24 V ^{2 BN}
RES ^{1 WH}
ADO ^{3 GN}
EDM ^{4 YE}
OSSD1 ^{5 GR}
OSSD2 ^{6 PK}
GND ^{7 BU}
FE ^{FE SH}
S1
B1 B3
Y1 13 23 33 41
1)
H3
UE10-3OS
B2 B4 Y2 14 24 34 42
0V
2) PELV
E119914/00/2014-07-29
Task
Connection of an M4000 Standard multiple light beam safety device to a UE10-3OS safety relay.
Operating mode: with restart interlock and external device monitoring.
Operating characteristics
When the light path is clear and the UE10-3OS is de-energized and functioning correctly, the yellow LED on the receiver and the H3
lamp flash. The system is ready for switch-on and waits for an input signal/switch-on signal. The system is enabled by pressing and
releasing the S1 button. The OSSD1 and OSSD2 outputs are live, the UE10-3OS is switched on. On interruption of one or several of
the light beams, the UE10-3OS is de-energized by the OSSD1 and OSSD2 outputs.
Fault analysis
OSSD cross-circuits and short-circuits are detected and lead to the inhibited state (lock-out). The erroneous behavior of the
UE10-3OS will be detected. The shutdown function is retained. On manipulation (e.g., jamming) of the S1 button, the system does
not enable the output current circuits.
Comments
1) _{Output circuits: These contacts are to be connected to the controller such that, with the output circuit open, the dangerous state}
is disabled. For categories 4 and 3, this integration must be dual-channel (x/y paths). Single-channel insertion in the control (z
path) is only possible with a single-channel control and by taking the risk analysis into account.
2) _{PELV in accordance with the requirements in EN 60204-1 / 6.4}
Take note of the operating instructions of the integrated devices.
6
OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK
Online data sheet | 2017-08-24 18:11:25
Subject to change without notice