S102S11 Datasheet, PDF (2/4 Pages) Sharp Electrionic Components – SIP Type SSR with Snubber Circuit and Mouning Capability for External Heat Sink

S102S11/S102S12/S202S11/S202S12
s Absolute Maximum Ratings
( Ta = 25˚C)
Input
Output
Parameter
Forward current
Reverse voltage
RMS ON-state current
*1_{Peak one cycle surge current}
Repetitive peak-OFF
state voltage
Non-repetitive peak-OFF
state voltage
Critical rate of rise of ON-state current
*2 _{Isolation voltage}
Operating temperature
Storage temperature
*3_{Soldering temperature}
Load supply voltage
S102S11/S102S12
S202S11/S202S12
S102S11/S102S12
S202S11/S202S12
S102S11/S102S12
S202S11/S202S12
Symbol
IF
VR
IT
I surge
V DRM
V DSM
dIT /dt
V iso
T opr
T stg
T sol
V out
Rating
50
6
*4₈
80
400
600
400
600
50
4 000
- 20 to + 80
- 30 to + 100
260
135
250
Unit
mA
V
A rms
A
V
V
A/µ s
V rms
˚C
˚C
˚C
V rms
*1 50Hz sine wave, start at Tj= 25˚C
*2 60Hz AC for 1 minute, RH= 40 to 60% , Apply voltages between input and output, by the dielectric withstand voltage
tester with zero-cross circuit.( Input and output shall be shorted respectively) .
( Note) When the isolation voltage is necessary at using external hear sink, please use the insulation sheet.
*3 For 10 seconds
*4 Tc <= 88˚C
s Electro-optical Characteristics
Parameter
Input
Forward voltage
Reverse current
ON-state voltage
Minimum
Operating current
S102S11/S102S12
S202S11/S202S12
Output
Open circuit
S102S11/S102S12
leak current
S202S11/S202S12
Critical rate of rise of OFF-state
voltage
Critical rate of rise of
Commutating OFF-state voltage
Zero-cross voltage S102S12/S202S12
Transfer
charac-
teristics
Minimum trigger
current
Isolation resistance
Turn-on time
S102S11/S202S11
S102S12/S202S12
S102S11/S202S11
S102S12/S202S12
Turn-off time
Thermal resistance
(Between junction and case)
Thermal resistance
(Between junction and ambience )
Symbol
VF
IR
VT
I op
I leak
dV/dt
( dV/dt )_C
V OX
I FT
R ISO
t on
t off
R th(j - c)
R th(j - a)
Conditions
IF = 20mA
VR = 3V
IT = 2Arms
Vout = 120Vrms
V out = 240Vrms
Vout = 120Vrms
Vout = 240Vrms
V D = 2/3V DRM
Tj = 125 ˚C
dI _t/dt = - 4.0A/ms,
*5
IF = 8mA
VD = 12V, R L = 30 Ω
VD = 6V, R L = 30 Ω
DC500V, RH = 40 to 60 %
AC60Hz
AC60Hz
-
-
*5 S102S11/S102S12 : VD= 400V S202S11/S202S12 : VD= 600V
MIN.
-
-
-
-
-
-
30
TYP.
1.2
-
-
-
-
-
-
(Ta = 25˚C )
MAX.
1.4
10 ^{- 4}
1.5
Unit
V
A
V rms
50
mA rms
5
mA rms
10
-
V/µ s
5
-
-
V/µ s
-
-
35
V
-
-
8
mA
-
-
8
mA
10 ¹⁰
-
-
Ω
-
-
1
ms
-
-
9.3
ms
-
-
9.3
ms
-
4.0
-
˚C/W
-
40
-
˚C/W