S101S15V Datasheet, PDF (1/4 Pages) Sharp Electrionic Components – SIP Type SSR with Built-in Snubber Circuit

S101S15V/S101S16V
S201S15V/S201S16V
S101S15V/S101S16V/S201S15V/S201S16V
SIP Type SSR with Built-in
Snubber Circuit
s Features
1. High radiation resin mold package
IT : MAX. 3A rms
2. Isolation voltage between input and output
Viso : 3 000 Vrms
3. Built-in zero-cross circuit
(S101S16V/ S201S16V)
4. Built-in snubber circuit
5. Recognized by UL, file No. E94758
Approved by CSA, file No. LR63705
s Applications
1. Air conditioners
2. OA equipment
s Model Line-ups
No built-in
zero-cross circuit
Built-in zero-cross
circuit
For 100V lines
S101S15V
S101S16V
For 200V lines
S201S15V
S201S16V
s Absolute Maximum Ratings (Ta = 25˚C )
Parameter
Forward current
Input
Reverse current
Output
RMS ON-state current
*1 Peak one cycle surge
current
Repetitive peak OFF-
state voltage
Critical rate of rise of
ON-state current
Operating frequency
Operating temperature
Storage temperature
*2 _{Isolation voltage}
*3 _{Soldering temperature}
Ratings
Symbol
Unit
100V line 200V line
IF
50
mA
VR
6
V
IT 3 ( Tc<=100˚C) A rms
I surge
30
A
V DRM 400 600 V
dIT /dt
40
A/µ s
f
45 to 65
HZ
T opr - 20 to + 80 ˚C
T stg - 30 to + 100 ˚C
V iso
3.0
kV rms
T sol
260
˚C
s Outline Dimensions
(Unit : mm )
Common to Pin No.1
A Model No, B
S101S15V _3A125VAC
S101S16V
S201S15V
S201S16V
3A265VAC
g
4 - 1.1 ^{± 0.2}
4 - 1.25 ^{± 0.3}
4 - 0.8 ^{± 0.2}
18.5 ^{± 0.2}
16.4 ^{± 0.3}
φ 3.2 ^{± 0.2}
Common to Pin No.1
5.5 ^{± 0.2}
A
B
+-
1 23 4
(5.08) (7.62)
Internal connection diagram
S101S15V/S201S15V
(2.54)
0.6^{± 0.1} (1.4)
g May not be externally
connected
S101S16V/S201S16V
Zero-cross
circuit
1 2 34
1 Output (Triac T2 )
2 Output (Triac T1 )
3 Input ( + )
4 Input ( - )
12
34
1 Output (Triac T2 )
2 Output (Triac T1 )
3 Input ( + )
4 Input ( - )
*1 60H Z sine wave, Tj = 25˚C
*2 AC 60Hz for 1 minute, 40 to 60% RH
Isolation voltage measuring method:
( 1) Dielectric withstand tester, with zero-cross circuit shall be used.
( 2) The waveform of applied voltage shall be sine wave.
( 3) It shall be applied voltage between input and output.
( Input and output shall be short-circuited respectively)
*3 For 10 seconds
“ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs,
data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.”