LT1W67A Datasheet, PDF (1/1 Pages) Sharp Electrionic Components – 1616 Size, 0.8mm Thickness, Compact Full Color Leadless Chip LED Device

Full Color Leadless Chip LED Device
LT1W67A
LT1W67A(Under Development)
1616 Size, 0.8mm Thickness,
Compact Full Color Leadless
Chip LED Device
s Outline Dimensions
(Unit : mm)
s Radiation Diagram
(Ta=25˚C)
1.6^±0.15
1.0
0.8
3
2
4
1
1.2
1.0
(0.4)
Recommended PWB pattern for soldering
Soldering area
1.2 0.6 1.2
1.Plating area
Resist
2.Pin connections
1 Anode(Yellow-green)
2 Anode(Red)
3 Anode(Blue)
4 Cathode(Common)
3.Unspecified tolerance:±0.2
-40˚
Yellow-green
-60˚
-80˚
-40˚
-60˚
-80˚
-20˚
0˚
+20˚
100
80
60
40
20
X
-20˚
0˚
+20˚
100
80
60
40
20
+40˚
Red
+60˚
+80˚
+40˚
Blue
+60˚
+80˚
s Absolute Maximum Ratings
YX
(Ta=25˚C)
Power dissipation Forward current Peak forward current ^{Derating factor} Reverse voltage Operating temperature Storage temperature Soldering temperature
Model No. Radiation color Radiation material P^*1
IF
IFM*2
(mA/˚C)
VR
Topr
Tstg
Tsol*3
(mW) (mA)
(mA)
DC Pulse
(V)
(˚C)
(˚C)
(˚C)
Blue
GaN on SiC
200
30
LT1W67A Yellow-green GaP
84
30
Red
GaAsP on GaP
84
30
100
0.67 1.33
5
-30 to +85 -40 to +100 260
50
0.40 0.67
5
-30 to +85 -40 to +100 260
50
0.40 0.67
5
-30 to +85 -40 to +100 260
*1 The value is specified under the condition that either color is lightened separately.
When all diodes are lightened simultaneously, the power dissipation of each diode should be less than 30% of the value specified in this table.
*2 Duty ratio=1/10, Pulse width=0.1ms
*3 For 3s or less at the temperature of hand soldering. Temperature of reflow soldering is shown on the below page.
s Electro-optical Characteristics
Lens
type
Model
No.
Radiation
color
Milky
diffusion
LT1W67A
Blue
Yellow-green
Red
Forward voltage
VF(V)
TYP MAX
4.4
5.6
2.1
2.8
2.0
2.8
Peak emission wavelength
λp(nm)
IF
TYP (mA)
430
20
565
20
635
20
Luminous intensity
IV(mcd) IF
TYP (mA)
6.5
20
13.0
20
8.5
20
Spectrum radiation bandwidth
∆λ(nm) IF
TYP (mA)
70
20
30
20
35
20
Reverse current
IR(µA) VR
MAX (V)
10
4
10
4
10
4
(Ta=25˚C)
Terminal capacitance Page for
Ct(pF)
characteristics
TYP ^(MHZ) diagrams
50
1
----
35
1
----
20
1
----
06 (Notice) ¡In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
(Internet) ¡Data for sharp's optoelectronic/power device is provided for internet.(Address http://www.sharp.co.jp/ecg/)