LT1541MN Datasheet, PDF (1/2 Pages) Sharp Electrionic Components – Dot Matrix LED Unit for Outdoor Use(Lamp Type,Water-proof Type)

Dot Matrix LED Unit for Outdoor Use LT1541MN(Lamp Type,Water-proof Type)
s Features
¡No. of dots : 16!16dots
¡Outline dimensions : 240!240mm
¡Dot size : 13.0!13.0mm(Using oval lamp)
¡Dot pitch : 14.9mm
¡Radiation color : Yellow-green+Red(High-luminosity)dichromatic type
¡Driving method : 1/8 duty dynamic drive
LT1541MN
s Absolute Maximum Ratings
Parameter
Supply voltage for IC
Supply voltage for LED
Input voltage
Turn-on time
Operating temperature
Storage temperature
Power dissipation
Symbol
VCC
VLED
V1
tON
Topr
Tstg
P
Rating
-0.3 to +6.0
-0.3 to +8.0
-0.3 to VCC+0.3
1
-20 to +75
-25 to +100
59
(Ta=25˚C)
Unit
V
V
V
ms
˚C
˚C
W
s Optical Characteristics
Parameter
Symbol
Viewing angle Horizontal 2θ¹/2
Peak emission wavelength ^Red λp
Yellow-green
(VCC=5V,VLED=7.5V,Ta=25˚C)
TYP.
Unit
70
˚
660
nm
565
s Luminance
Luminance is classified into 2 ranks shown below.
(VCC=5V,VLED=7.5V,Ta=25˚C)
Radiation color
Red
Yellow-green
1
1 300
1 000
Rank
2
1 690
1 300
Unit
cd/m²
s Terminal Functions
Connector
Power
supply
(CN1)
Input
signal
(CN2)
Symbol
VLED
Vcc
GND1
GND2
A0 to A2
RDATA
GDATA
LATCH
RENABLE
GENABLE
CLOCK
Function
Supply voltage for LED(+7.5V)
Supply voltage for IC(+5V)
Ground for IC
Ground for LED
Address specification signal for column driver
Serial data input for each color(H:ON, L:OFF)
Shift from up to down in the unit
HD16/HD31/HD0/HD15
Latch signal of display data H: Serial data is converted to
parallel data. L: Contents are latched.
LATCH signal is set up after switching address(A0 to A2)
Controls ON/OFF of each color of LED
(H: LED OFF)
Clock signal for data transmission in the shift-
register.(L/H: serial data is shifted.)
GND1 Ground for signal(Connected to ground for IC)
A0 to A2 Buffered input signal
RDATA Input signal generated through 32-bit shift register
Output
signal
(CN3)
GDATA
LATCH Buffered input signal
RENABLE
GENABLE
Buffered input signal
CLOCK Buffered input signal
GND1 Ground for signal(Connected to ground for IC)
Each signal is used as input signal for next unit.
* As for the terminal number, refer to the outline dimensions.
s Electrical Characteristics
(VCC=5V,VLED=7.5V,Ta=25˚C)
Parameter
Symbol MIN. TYP. MAX. Unit
Supply voltage for IC
VCC
4.75 5.0 5.25 V
Supply voltage for LED
VLED
7.0 7.5 7.75 V
IC current dissipation
ICC
LED current dissipation^*1 ILED
------ 200 500 mA
------ 5.5 7.0 A
Input voltage
VIH
3.5 ------
VIL
------ ------
Input current
IIH
------ ------
IIL
------ ------
Clock frequency
fCLK
------ ------
Frame frequency
fFR
250 400
*1 Under the condition that dichromatic all dots are lit.
------
1.5
0.1
0.12
10.0
3 000
V
V
µA
mA
MHZ
HZ
s Timing Chart
tSU
th
tWCLK
CLOCK
RDATA
GDATA
RDATA out
GDATA out
VD(n+1) data
tdD
LATCH
Internal
ENABLE
t=1/fosc
ON ON
ON
td(C-L)
td(L-C)
tWL
ON
OFF ON
VD(n+2) data
ON
ON
OFF
RENABLE
GENABLE
ADDRESS
(A0 to A2)
VD(n) data ON
td(E-A)
VD(n)
s Block Diagram
VD(n+1) data ON
td(A-E)
td(A-L)
VD(n+1)
tWKNA
Input/output circuit
473
331
HC367
A0
A1
A2
RENABLE
RDATA
GDATA
LATCH
GENABLE
CLOCK
GND1
OUT
Luminance adjustment circuit
GADJ RADJ
OSC MONO-MULTI
3 to 8 DECODER
GATE
IN
A0
A1
A2
RENABLE
RDATA
GDATA
LATCH
GENABLE
CLOCK
GND1
HD16
PNP DRIVER
HD16
16!16
HD31
HD0
Dot
matrix
LED
HD31
HD0
HD15
HD15
SELECTOR
17 (Notice) ¡In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
(Internet) ¡Data for sharp's optoelectronic/power device is provided for internet.(Address http://www.sharp.co.jp/ecg/)