GP1A73A Datasheet, PDF (1/4 Pages) Sharp Electrionic Components – Compact OPIC Photointerrupter with Connector

GP1A73A/GP1A73A1
GP1A73A/GP1A73A1
Compact OPIC Photointerrupter
with Connector
s Features
1. Compact type
2. TTL compatible owing to OPIC output
3. Snap-in mounting type
4. 3 kinds of mounting plate thickness
(Applicable plate thickness : 1.0, 1.2 and 1.6 mm)
s Applications
1. Copiers
2. Laser beam printers
3. Facsimiles
s Outline Dimensions
GP1A73A
( 6.8)
(Unit : mm)
(Case surface)
13.6
1.6
4.3 5.0 4.3 6.8 ± 1
JAPAN AMP made
connector 175487-3
4.7
2-0.5 ± 0.1
(Slit)
1 : VCC
2 : Vout
3 : GND
1.2
0.75
GP1A73A1
2.4
5.4
6.9
9.9
11.4
14.0
16.8
17.0
( 5)
2-0.9
2-0.5 4.0
* Unspecified tolerances
shall be as follows.
* ( ) : Connector dimensions
for reference
Dimension
d < 5.0
5.0<= d < 15.0
15.0 <= d
Tolerance
± 0.15
± 0.2
± 0.3
* "OPIC" (Optical IC) is a trademark of the SHARP Corporation.
An OPIC consists of a light-detecting element and signal-processing circuit
integrated onto a single chip.
s Absolute Maximum Ratings
(Ta=25˚C)
Parameter
Supply voltage
*1 _{Output voltage}
*2 _{Low level output current}
*3 _{Operating temperature}
*3 _{Storage temperature}
Symbol Rating Unit
VCC - 0.5 to + 7 V
V out - 0.5 to + 7
V
IOL
8
mA
T opr - 20 to + 75 ˚C
T stg - 30 to + 85 ˚C
*1 Output transistor collector-emitter voltage
*2 Output transistor collector current
*3 The connector should be plugged in/out at normal temperature.
(Case surface)
13.6
1.6
4.3 5.0 4.3 5.0 ^± 1
HIROSE made
connector DF3A-3P-2DSA
4.7
2-0.5 ± 0.1
(Slit)
3 : VCC
2 : Vout
1 : GND
2.4
5.4
2-0.9
2-0.5 4.0
6.9
9.9
11.4
14.0
1.2
16.8
0.75
17.0
* Unspecified tolerances
shall be as follows.
* ( ) : Connector dimensions
for reference
Dimension
d < 5.0
5.0<= d < 15.0
15.0 <= d
Tolerance
± 0.15
± 0.2
± 0.3
s Internal Connection Diagram (Both GP1A73A/GP1A73A1)
Constant
voltage circuit
GND
Vout
Connector terminal No.
GP1A73A GP1A73A1
3 : GND 1 : GND
2 : Vout 2 : Vout
1 : Vcc 3 : Vcc
Amp.
Vcc
* GP1A73A and GP1A73A1 are different in the terminal marking number of
connectors from each other due to use of connectors of different manufacturers.
“ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs,
data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.”