SGM811 Datasheet, PDF (4/9 Pages) SG Micro Corp – Microprocessor Supervisory with Manual Reset Input

ELECTRICAL CHARACTERISTICS (continued)
(V_CC Typ = 5 V for L/M/J Models, 3.3 V for T/S Models, 3 V for R Models, 2.5 V for Z Models; unless otherwise noted.)
PARAMETER
RESET/ RESET OUTPUT VOLTAGE
CONDITIONS
Low (SGM811R/S/T/Z)
VCC = VTH(MIN), ISINK = 1.2mA
Low (SGM811L/M/J)
VCC = VTH(MIN), ISINK = 3.2mA
Low (SGM811R/S/T/Z/L/M/J) VCC > 1.0 V, ISINK = 50µA
High (SGM811R/S/T/Z)
VCC > VTH(MAX), ISOURCE = 500µA
High (SGM811L/M/J)
VCC > VTH(MAX), ISOURCE = 800µA
Low (SGM812R/S/T/Z)
VCC = VTH(MAX), ISINK = 1.2mA
Low (SGM812L/M/J)
VCC = VTH(MAX), ISINK = 3.2mA
High (SGM812 R/S/T/Z/L/M/J) 1.8 V < VCC < VTH(MIN), ISOURCE = 150µA
MIN TYP MAX UNITS
0.8×VCC
VCC– 1.5
0.8×VCC
0.3
V
0.4
V
0.3
V
V
V
0.3
V
0.4
V
V
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS
(Typical values are at TA = 25°C, unless otherwise noted.)
Terminal Voltage (With Respect to Ground)
VCC................................................................................–0.3 V to +6 V
All Other Inputs ............................................ –0.3 V to VCC + 0.3 V
Input Current
VCC , MR ................................................................................ 20 mA
Output Current
RESET, RESET ..................................................................... 20 mA
Power Dissipation, PD @ TA = 25℃
SOT23-5 .....................................................................................0.4W
SOT143-4.................................................................................. 0.32W
Operating Temperature Range...........................- 40°C to +125°C
Junction Temperature...........................................................+150°C
Storage Temperature.............................................- 65°C to +150°C
Lead Temperature (soldering, 10s).....................................+260°C
ESD Susceptibility
HBM..........................................................................................4000V
MM..............................................................................................400V
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational
sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
PIN DESCRIPTION
Pin Number
NAME
SGM811
SGM812
SOT143-4 SOT23-5 SOT143-4
FUNCTION
GND
1
1
1
Ground
NC
2
No connect.
RESET
2
Active Low Logic Output. RESET remains low while VCC is below the reset
3
— threshold or when MR is low; RESET then remains low for at least 160 ms after
VCC rises above the reset threshold.
Active High Logic Output. RESET remains high while VCC is below the reset
RESET —
—
MR
3
4
2
threshold or when MR is low; RESET then remains high for 240 ms (typical) after
VCC rises above the reset threshold.
Manual Reset. This active low debounced input will ignore input pulses of 100 ns or
3
less (typical) and is guaranteed to accept input pulses of greater than 10 µs. Leave
floating when not used.
VCC
4
5
4
Power supply voltage that is monitored.
4
SGM811/812