LC89512W Datasheet, PDF (5/5 Pages) Sanyo Semicon Device – CD-ROM Error Correction LSI with Built-In SCSI Interface

LC89512W
Specifications
Absolute Maximum Ratings at V_SS = 0 V
Parameter
Maximum supply voltage
I/O voltages
Allowable power dissipation
Operating temperature
Storage temperature
Soldering thermal stress limit (pins only)
Symbol
V_DD max
V_I V_O
Pd max
Topr
Tstg
Ta = 25°C
Ta = 25°C
Ta ≤ 70°C
10 seconds
Conditions
Ratings
Unit
–0.3 to +7.0
V
–0.3 to V_DD + 0.3
V
350
mW
–30 to +70
°C
–55 to +125
°C
260
°C
Allowable Operating Ranges at Ta = –30 to +70°C, V_SS = 0 V
Parameter
Symbol
Conditions
Supply voltage
V_DD
Input voltage range
V_IN
min
typ
max
Unit
4.5
5.0
5.5
V
0
V_DD
V
DC Characteristics at Ta = –30 to +70°C, V_SS = 0 V, V_DD = 4.5 to 5.5 V
Parameter
Input high level voltage
Input low level voltage
Input high level voltage
Input low level voltage
Input high level voltage
Input low level voltage
Output high level voltage
Output low level voltage
Output low level voltage
Output low level voltage
Input leakage current
Pull-up resistance
Symbol
Conditions
min
V_IH1
All input pins other than (1), (3), and XTALCK
2.2
V_IL1
V_IH2
RESET, I_O0 to I_O7, D0 to D7, RD, CS, WR, WFCK,
2.5
V_IL2
SBSO and SCOR(1)
V_IH3
ACK, ATN and the input pins (3)
2.0
V_IL3
V_OH1
I_OH1 = –3 mA: I_O0 to I_O7, D0 to D7 and all output pins
other than (2), (3) and XTALCK
2.4
V_OL1
I_OL1 = 3 mA: I_O0 to I_O7, D0 to D7 and all output pins
other than (2), (3) and XTALCK
V_OL2
I_OL2 = 3 mA: INT1 and INT0
(pull-up resistor open drain) (2)
V_OL3
I_OL3 = 48 mA: DB0 to DB7, DBP, BSY, I/O, MSG, SEL,
RST, REQ, C/D (2)
I_L
V_I = V_SS, V_DD: All input pins
–25
R_UP
I_O0 to I_O7, D0 to D7, INT1 and INT0
40
typ
max
Unit
V
0.8
V
V
0.6
V
V
0.8
V
V
0.4
V
0.4
V
0.4
V
+25
µA
80
160
kΩ
s No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace
equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of
which may directly or indirectly cause injury, death or property loss.
s Anyone purchasing any products described or contained herein for an above-mentioned use shall:
ΠAccept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and
distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all
damages, cost and expenses associated with such use:
 Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on
SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees
jointly or severally.
s Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for
volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied
regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of February, 1997. Specifications and information herein are subject to
change without notice.
No. 4852-5/5