|
LC87F2832A_09 Datasheet, PDF (4/27 Pages) Sanyo Semicon Device – FROM 32K byte, RAM 1024 byte on-chip 8-bit 1-chip Microcontroller | |||
|
◁ |
LC87F2832A
ÂOscillation Circuits
⢠RC oscillation circuit (internal):
For system clock
⢠CF oscillation circuit:
For system clock, with internal Rf
⢠Crystal oscillation circuit:
For low-speed system clock, with internal Rf
⢠Frequency variable RC oscillation circuit (internal): For system clock
1) Adjustable in ±4% (typ) step from a selected center frequency.
2) Measures oscillation clock using a input signal from XT1 as a reference.
ÂSystem Clock Divider Function
⢠Can run on low current.
⢠The minimum instruction cycle selectable from 300ns, 600ns, 1.2μs, 2.4μs, 4.8μs, 9.6μs, 19.2μs, 38.4μs,
and 76.8μs (at a main clock rate of 10MHz).
ÂStandby Function
⢠HALT mode: Halts instruction execution while allowing the peripheral circuits to continue operation.
1) Oscillation is not halted automatically.
2) Canceled by a system reset or occurrence of an interrupt
⢠HOLD mode: Suspends instruction execution and the operation of the peripheral circuits.
1) The CF, RC, Xâtal, and frequency variable RC oscillators automatically stop operation.
2) There are three ways of resetting the HOLD mode.
(1) Setting the reset pin to the low level.
(2) Setting at least one of the INT0, INT1, INT2, INT4, and INT5 pins to the specified level
(3) Having an interrupt source established at port 0
⢠X'tal HOLD mode: Suspends instruction execution and the operation of the peripheral circuits except the base timer.
1) The CF, RC, and frequency variable RC oscillators automatically stop operation.
2) The state of crystal oscillation established when the X'tal HOLD mode is entered is retained.
3) There are four ways of resetting the X'tal HOLD mode.
(1) Setting the reset pin to the low level
(2) Setting at least one of the INT0, INT1, INT2, INT4, and INT5 pins to the specified level
(3) Having an interrupt source established at port 0
(4) Having an interrupt source established in the base timer circuit
ÂOn-chip Debugger
⢠Supports software debugging with the IC mounted on the target board (LC87D2832A).
LC87F2832A has a On-chip debugger but its function is limited.
ÂPackage Form
⢠TQFP64J (7 à 7):
⢠FLGA68K (6.0 à 6.0):
⢠FLGA64 (5.0 à 5.0):
Lead-/Halogen-free type
Lead-/Halogen-free type
Lead-/Halogen-free type
ÂDevelopment Tools
⢠On-chip debugger: TCB87- TypeB + LC87D2832A
ÂProgramming Boards
Package
TQFP64J (7Ã7)
FLGA68K (6.0Ã6.0)
FLGA64 (5.0Ã5.0)
Programming boards
W87F58256TQ7
W87F58256FL6 * This board is Built To Order. It may take about a month to deliver.
W87F59256FL5 * This board is Built To Order. It may take about a month to deliver.
ÂFlash ROM Programmer
Maker
Flash Support Group, Inc.
(Formerly Ando Electric Co., Ltd.)
Model
AF9708/AF9709/
AF9709B
SANYO
SKK (SANYO FWS)
Note: Please check the latest version.
Supported version (Note)
After 02.57
Application Version: After 1.03
Chip Data Version: After 2.03
Device
LC87F2832A
LC87F2832A
No.A0478-4/27
|
▷ |