LC88F5LA4ACS Datasheet, PDF (28/33 Pages) Sanyo Semicon Device – FROM 96K byte, RAM 6K byte on-chip 16-bit 1-chip Microcontroller

LC88F5LA4ACS
Continued from preceding page.
Parameter
Symbol
Applicable
Pin/Remarks
Conditions
VDD[V]
min
HALT mode
consumption
current
(Note 7-1)
IDDHALT(1)
VDD1
=VDD2
=VDDA
≥VDD3
• HALT mode
• FmCF=10MHz ceramic oscillation mode
• FmMRC=0MHz (oscillation stoped)
• FmX'tal=32.768kHz crystal oscillation mode
• System clock set to 10MHz
2.6 to 3.6
• Internal RC oscillation stopped
Specification
typ
max unit
1.18
2.0
• 1/1 frequency division mode
IDDHALT(2)
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FmMRC=10MHz oscillator mode
• FmX'tal=32.768kHz crystal oscillation mode
2.6 to 3.6
1.05
1.8
• System clock set to 10MHz
• Internal RC oscillation stopped
• 1/1 frequency division mode
mA
IDDHALT(3)
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FmMRC=4MHz oscillator mode
• FmX'tal=32.768kHz crystal oscillation mode
• System clock set to 4MHz
2.2 to 3.6
0.44
0.8
• Internal RC oscillation stopped
• 1/1 frequency division mode
IDDHALT(4)
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FmMRC=0Hz (oscillation stopped)
• FmX'tal=32.768kHz crystal oscillator mode
2.2 to 3.6
0.12
0.5
• System clock set to internal RC oscillation
• 1/1 frequency division mode
IDDHALT(5)
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FmMRC=0Hz (oscillation stopped)
• FmX'tal=32.768kHz crystal oscillator mode
• System clock set to 32.768kHz
• Internal RC oscillation stopped
2.2 to 3.6
8.21
40
HOLD mode
consumption
current
IDDHOLD(1)
VDD1
• 1/1 frequency division mode
HOLD mode
• CF1=VDD or open (external clock mode)
2.2 to 3.6
μA
0.02
20
HOLDX
IDDHOLD(2)
HOLDX mode
mode
consumption
• CF1=VDD or open (external clock mode)
• FmX'tal=32.768kHz crystal oscillator mode
2.2 to 3.6
5.2
35
current
Note 7-1: The consumption current value includes none of the currents that flow into the output transistor and internal
pull-up resistors.
F-ROM Programming Characteristics at Ta = +10°C to +55°C, VSS1=VSS2=VSSA=0V
Parameter
Onboard
programming
Symbol
IDDFW(1)
Applicable
Pin/Remarks
VDD1
Conditions
• Microcontroller erase current current is
excluded.
VDD[V]
min
2.6 to 3.6
Specification
typ
max
unit
7 mA
current
Onboard
programming
time
tFW(1)
tFW(2)
• 128-/1K-byte erase operation
• 2-byte programming operation
2.6 to 3.6
2.6 to 3.6
30 ms
60 μs
No.A1860-28/33