|
LV1041M Datasheet, PDF (2/3 Pages) Sanyo Semicon Device – Dolby Prologic Decoder | |||
|
◁ |
LV1041M
Specifications
Maximum Ratings at Ta = 25°C
Parameter
Maximum supply voltage
Allowable power dissipation
Operating temperature
Storage temperature
Symbol
VCC max
Pd max
Topr
Tstg
Conditions
Ta ⤠70°C
When mounted on a 114.3 Ã 76.1 Ã 1.6 mm fiberglass
epoxy printed circuit board.
Ratings
Unit
12
V
1300
mW
â20 to +70
°C
â40 to +150
°C
Operating Conditions at Ta = 25°C
Parameter
Recommended supply voltage
Operating supply voltage range
Input high-level voltage
Input low-level voltage
Dolby level
Symbol
VCC
VCC op
VIH
VIL
VO Dolby
Conditions
Ratings
9
8 to 10
3.5 to 5.5
0 to 1.0
300
Unit
V
V
V
V
mVrms
Operating Conditions
at Ta = 25°C, VCC = 9 V, VIN = 300 mV rms (left and right inputs), 0.707 à 300 mV rms (center and surround
inputs), f = 1 kHz, center trim = 0 dB, surround trim = 0 dB, delay time = 20 ms, in wide mode, and with the
center and surround master volume set to 0 dB.
Parameter
Symbol
Conditions
Quiescent current
Center channel output level
Output level deviation
Matrix rejection (L)
Matrix rejection (C)
Matrix rejection (R)
Matrix rejection (S)
Total harmonic distortion (L)
Total harmonic distortion (C)
Total harmonic distortion (R)
Total harmonic distortion (S)
Signal-to-noise ratio (L)
Signal-to-noise ratio (C)
Signal-to-noise ratio (R)
Signal-to-noise ratio (S)
Signal handling (L)
Signal handling (C)
Signal handling (R)
Signal handling (S)
Noise sequencer output level
Noise reduction frequency
characteristics
[Prologic Off Mode]
Left and right channels total
harmonic distortion
Left and right channels signal-to-
noise ratio
Left and right channels signal
handling
Master volume muting attenuation
ICC
VOC
VOL
RjL
RjC
RjR
RjS
THDL
THDC
THDR
THDS2
SN/L
SN/C
SN/R
SN/S
SHL
SHC
SHR
SHS
Vns
Dec1
Dec2
Dec3
Dec4
Dec5
THDOFF
S/NOFF
Shoff
VMUTE
No signal
C input
L, R, Sch from Cch, matrix output
L input
C input
R input
S input
L 24-pin output
C 31-pin output
R 21-pin output
S delay 33-pin output
L 24-pin output, CCIR/ARM, RS = 10 kâ¦
C 31-pin output, CCIR/ARM, RS = 10 kâ¦
R 21-pin output, CCIR/ARM, RS = 10 kâ¦
S delay 33-pin output
L 24-pin output, VCC = 8.5 V, THD = 1%
C 31-pin output, VCC = 8.5 V, THD = 1%
R 21-pin output, VCC = 8.5 V, THD = 1%
VCC = 8.5 V, THD = 3%, output 33-pin S delay
Each matrix out
0 dB, 1 kHz
â20 dB, 1 kHz
0 dB, 5 kHz
â20 dB, 5 kHz
â40 dB, 5 kHz
L, R, 400 to 30 kHz BPF
L, R, CCIR/ARM
L, R, VCC = 8.5 V, THD = 1%
VIN = 1 Vrms
min
â2
â0.5
15
15
15
15
53
â1.5
â24.0
â1.5
â23.3
â46.8
Ratings
typ
80
0
0
â40
â40
â40
â40
0.02
0.02
0.02
0.1
â76
â77
â76
â75
16
17
16
16
60
0.0
â22.5
0.0
â21.8
â45.3
Unit
max
110 mA
+2
dB
+0.5
dB
â25
dB
â25
dB
â25
dB
â25
dB
0.09
%
0.09
%
0.09
%
0.7
%
â71
dB
â71
dB
â71
dB
â65
dB
dB
dB
dB
dB
90 mV
+1.5
dB
â21.0
dB
+1.5
dB
â20.3
dB
â43.8
dB
0.01
0.03
%
â90
â80
dB
15
16
dB
â92
â80
dB
No. 5889-2/19
|
▷ |