LC897127K Datasheet, PDF (2/14 Pages) Sanyo Semicon Device – SCSI CD-ROM Decoder with On-Chip DVD Interface

LC897127K
Specifications
Absolute Maximum Ratings at V_SS = 0 V
Parameter
Maximum supply voltage
Input/output voltage
Allowable power dissipation
Operating temperature
Storage temperature
Soldering temperature (pin part only)
Symbol
V_DD max
V_IV_O
Pd max
Topr
Tstg
Ta = 25°C
Ta = 25°C
Ta ≤ 70°C
10s
Conditions
Ratings
Unit
–0.3 to +7.0
V
–0.3 to V_DD +0.3
V
550
mW
–30 to +70
°C
–55 to +125
°C
260
°C
Allowable Operating Ranges at Ta = –30 to +70°C, V_SS = 0 V
Parameter
Supply voltage
Input voltage range
Symbol
V_DD
V_IN
Conditions
min
4.5
0
Ratings
typ
5.0
Unit
max
5.25
V
V_DD
V
DC Characteristics at Ta = –30 to +70°C, V_SS = 0 V, V_DD = 4.5 to 5.5 V
Parameter
Input high-level voltage
Input low-level voltage
Input high-level voltage
Input low-level voltage
Input high-level voltage
Input low-level voltage
Input high-level voltage
Input low-level voltage
Input high-level voltage
Input low-level voltage
Input high-level voltage
Input low-level voltage
Input high-level voltage
Input low-level voltage
Output high-level voltage
Output low-level voltage
Output high-level voltage
Output low-level voltage
Output high-level voltage
Output low-level voltage
Output low-level voltage
Input leakage current
Pull-up resistance
Pull-down resistance
Applicable pin sets are as follows.
Symbol
Conditions
V_IH1
V_IL1
V_IH2
V_IL2
V_IH3
V_IL3
V_IH3
V_IL3
V_IH4
V_IL4
V_IH4
V_IL4
VI_H5
V_IL5
V_OH1
V_OL1
V_OH2
V_OL2
V_OH2
V_OL2
V_OL4
I_IL
R_UP
R_DOWN
TTL levels
TTL levels
with pull-up resistor
TTL levels
Schmitt
TTL levels
Schmitt with pull-down resistor
TTL levels
Schmitt with pull-up resistor
CMOS levels
Schmitt
I_OH1 = –12 mA
I_OL1 = 12 mA
I_OH2 = –8 mA
I_OL2 = 8 mA
I_OH2 = –2 mA
I_OL2 = 2 mA
I_OL4 = 48 mA
V_I = V_SS, V_DD
Applicable pins
Ratings
Unit
min
typ
max
2.2
(1)
V
0.8
V
2.2
—
—
V
(9)
—
—
0.8
V
2.2
—
—
V
(2)
—
—
0.8
V
2.2
—
—
V
(11)
—
—
0.8
V
2.2
—
—
V
(12)
—
—
0.8
V
(3)
(4), (8), (10)
0.8 V_DD
—
2.0
—
—
V
— 0.2 V_DD
V
—
V
0.8
V
(6)
V_DD – 2.1
—
—
V
—
—
0.4
V
2.4
(7), (11)
—
V
0.4
V
2.4
(9), (5)
—
V
0.4
V
(10)
0.4
V
All input pins
–25
+25
µA
(5), (9)
60
120
240
kΩ
(11)
60
120
240
kΩ
INPUT (1) TEST0 to TEST4, CSCTRL, SUA0 to SUA6, C2PO, SDATA, BCK, LRCK, SCOR, WFCK, SBS0, MCK2SEL
(2) RESET
(3) CS, RD, WR
(4) SCSISEL, XTALSEL
OUTPUT (5) INT0, INT1, SWAIT
(6) MCK
(7) EXCK, DSDATA, DLRCK, DBCK, RAS0, CAS0, CAS1, OE, UWE, LWE, RA0 to RA8, HDBDIR
INOUT (8) ACK, ATN
(9) D0 to D7, IO0 to IO15
(10) DB0 to DB7, DBP, BSY, I/O, MSG, SEL, RST, REQ, C/D
(11) DRESP, DREQ, HDB0 to HDB7
(12) IOP0 to IOP7 (No pull-up resistor used when these pins are used as pins HDB0 to HDB7)
Note: Pins XTAL0, XTALCK0, XTAL1, XTALCK1, and X1EN are not included in DC characteristics.
No. 6251-2/14