LC895196K Datasheet, PDF (2/12 Pages) Sanyo Semicon Device – ATA-PI Compatible CD-ROM Decoder IC

LC895196K
Allowable Operating Ranges at Ta = –30 to +70°C, V_SS = 0 V
Parameter
Supply voltage
Input voltage range
Symbol
V_DD
V_IN
Conditions
min
4.5
0
Ratings
typ
5.0
DC Characteristics at V_SS = 0 V, V_DD = 4.5 to 5.5 V, Ta = –30 to +70°C
Parameter
Symbol
Conditions
Applicable pins (see below)
Ratings
min
typ
Input high level voltage
V_IH1 TTL compatible (1)
2.2
Input low level input
V_IL1 TTL compatible (1)
Input high level voltage
V_IH2 TTL compatible with pull-up resistor: (10)
2.2
Input low level input
V_IL2 TTL compatible with pull-up resistor: (10)
Input high level voltage
V_IH3 TTL compatible Schmitt: (2), (3), (11)
2.2
Input low level input
V_IL3 TTL compatible Schmitt: (2), (3), (11)
Output high level voltage
V_OH1 I_OH = –2 mA: (4), (10)
V_DD – 2.1
Output low level voltage
V_OL1 I_OL = 2 mA: (4), (10)
Output high level voltage
V_OH2 I_OH = –8 mA: (5)
V_DD – 2.1
Output: Low level voltage
V_OL2 I_OL = 8 mA: (5)
Output high level voltage
V_OH3 I_OH = –4 mA: (8), (11)
V_DD – 2.1
Output low level voltage
V_OL3 I_OL = 24 mA: (8), (11)
Output low level voltage
V_OL4 I_OL = 24 mA: (9)
Output low level voltage
V_OL5 I_OL = 8 mA: (6), (7)
Input leakage current
I_IL
V_I = V_SS, V_DD: (1), (2), (3), (11)
–10
Output leakage current
I_OZ When high impedance output: (6), (8), (9), (11)
–10
Pull-up resistor
R_UP (7), (10)
40
80
Note: The applicable pins correspond to the following names.
[INPUT]
(1) ..........ATPINSEL, CSCTRL, SUA0 to SUA6, BCK, C2PO, LRCK, SDATA, SBSO, SCOR, WFCK, TEST0 to TEST1
(2) ..........ZRESET, ZCS, ZRD, ZWR, CSEL
(3) ..........DA0 to DA2, ZCS1FX, ZCS3FX, ZDIOR, ZDIOW, ZDMACK, ZHRST
[OUTPUT]
(4) ..........RA0 to RA8, ZCAS0, ZCAS1, ZUWE, ZLWE, ZOE, ZRAS0, EXCK
(5) ..........MCK, MCK2, MCK3
(6) ..........ZRSTCPU, ZRSTIC
(7) ..........ZINT, ZINT1, ZSWAIT
(8) ..........DMARQ, HINTRQ
(9) ..........IORDY, ZIOCS16
[INPUT]
(10) ..........D0 to D7, IO0 to IO15
(11) ..........DD0 to DD15, ZDASP, ZPDIAG
* The XTAL0, XTALCK0, XTAL1, XTALCK1 pins are not included in the CD characteristics.
Recommended Example of Oscillator Circuit
Unit
max
5.5
V
V_DD
V
Unit
max
V
0.8
V
V
0.8
V
V
0.8
V
V
0.4
V
V
0.4
V
V
0.4
V
0.4
V
0.4
V
+10
µA
+10
µA
160
kΩ
R1 = 1 MΩ
R2 = 47 Ω
C1 = 0
C2 = 47 pF
Ceramic oscillator frequency = 33.8688 MHz.
The 33.8688 MHz recommended example is for a 3× overtone.
Because the specific values are influenced by the circuit board,
confer with the oscillator manufacturer.
No. 5852-2/12