LC895126 Datasheet, PDF (2/7 Pages) Sanyo Semicon Device – CD-ROM Decoder with Built-in SCSI Interface

LC895126
Electrical Characteristics at Ta = –30 to +70°C, V_SS = 0 V, V_DD = 4.5 to 5.5 V
Parameter
Input high-level voltage
Input low-level voltage
Input high-level voltage
Input low-level voltage
Input high-level voltage
Input low-level voltage
Input high-level voltage
Input low-level voltage
Input high-level voltage
Input low-level voltage
Output high-level voltage
Output low-level voltage
Output high-level voltage
Output low-level voltage
Output high-level voltage
Output low-level voltage
Output low-level voltage
Input leakage current
Pull-up resistance
Symbol
Conditions
V_IH1
V_IL1
V_IH2
V_IL2
V_IH3
V_IL3
V_IH4
V_IL4
V_IH5
V_IL5
V_OH1
V_OL1
V_OH2
V_OL2
V_OH2
V_OL2
V_OL4
I_IL
R_UP
TTL level pins: (1)
TTL level pins: (9)
Pins with built-in pull-up resistors.
TTL level pins: (2)
Schmitt input pins
CMOS level pins: (3)
Schmitt input pins
(4), (8), (10)
I_OH1 = –12 mA : (6)
I_OL1 = 12 mA : (6)
I_OH2 = –8 mA : (7)
I_OL2 = 8 mA : (7)
I_OH2 = –2 mA : (9), (5)
I_OL2 = 2 mA : (9), (5)
I_OL4 = 48 mA : (10)
V_I = V_SS or V_DD: All input pins.
(5), (9)
Ratings
Unit
min
typ
max
2.2
V
0.8
V
2.2
V
0.8
V
2.2
V
0.8
V
0.8 V_DD
2.0
V
0.2 V_DD
V
V
0.8
V
V_DD – 2.1
V
0.4
V
2.4
V
0.4
V
2.4
V
0.4
V
0.4
V
–25
+25
µA
60
120
240
kΩ
The pin sets referred to above are as follows:
INPUT
(1) TEST0 to TEST4, CSCTRL, SUA0 to SUA6, X1EN, WFCK, SBS0
(2) C2PO, SDATA, BCK, LRCK, SCOR, ZRESET
(3) ZCS, ZRD, ZWR
(4) SCSISEL, XTALSEL
OUTPUT
(5) ZINT0, ZINT1, ZSWAIT
(6) MCK, MCK2, MCK3
(7) EXCK, DSDATA, DLRCK, DBCK, ZRAS0, ZRAS1, ZCAS0, ZCAS1, ZOE, ZUWE, ZLWE, RA0 to RA8
INOUT
(8) ACK, ATN
(9) D0 to D7, IO0 to IO15, IOP0 to IOP4
(10) DB0 to DB7, DBP, BSY, I/O, MSG, SEL, RST, REQ, C/D
Note: The XTAL0, XTALCK0, XTAL1, and XTALCK1 pins are not covered by the electrical characteristics.
SCSI Interface Pin Input Characteristics
Parameter
Input threshold voltage
Hysteresis
Symbol
Conditions
V_{t + t1}
V_{t – t1}
∆V_tt1
V_DD = 4.50 to 5.50 V
V_DD = 5.0 V
min
0.80
0.41
Ratings
typ
1.60
1.10
0.5
Unit
max
2.00
V
V
V
Active Negation Output Characteristics
Parameter
Symbol
Conditions
Output high-level voltage
Output low-level voltage
V_OH
V_OL
I_OH = –24 mA
I_OL = 48 mA
Note: Active negation refers to the DB0 to DB7, REQ, and DBPB outputs.
min
2.5
Ratings
typ
Unit
max
V
0.4
V
Figure 1
No. 5786-2/7