LB11660RV Datasheet, PDF (2/9 Pages) Sanyo Semicon Device – Single-Phase Full-Wave Driver

LB11660RV
Absolute Maximum Ratings at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
Unit
VCC maximum power supply voltage
VM maximum power supply voltage
VCC max
VM max
20
V
20
V
OUT pin maximum output current
OUT pin output withstand voltage 1
OUT pin output withstand voltage 2
PRE pin maximum source current
IOUT max
VOUT max1
VOUT max2
IPSO max
Rf≥0.39Ω
T≤0.4µs
1.5
A
20
V
26.5
V
30
mA
PRE pin maximum sink current
IPSI max
-7
mA
PRE pin output withstand voltage
VP max
20
V
HB maximum output current
HB
10
mA
VTH input pin withstand voltage
VTH max
7
V
RD output pin output withstand voltage
VRD max
18
V
RD output current
IRD max
10
mA
Allowable power dissipation
Pd max
Mounted on a specified board *1
0.8
W
Operating temperature range
Topr
*2
-30 to 95
°C
Storage temperature range
Tstg
-55 to 150
°C
*1 A circuit board for mounting (114.3mm×76.1mm×1.6mm, glass epoxy resin)
*2 Tj max = 150°C. Must be used within the operating temperature range in which Tj does not exceed 150°C.
Recommended Operating Range at Ta = 25°C
Parameter
VCC power supply voltage
VM power supply voltage
Current limiter operating range
VTH input level voltage range
Hall input common phase input voltage range
Symbol
VCC
VCC
ILIM
VTH
VICM
Conditions
Ratings
Unit
4 to 15
V
3 to 15
V
0.6 to 1.2
A
0 to 6
V
0.2 to 3
V
Electrical Characteristics at Ta = 25°C, VCC = 12V, unless otherwise specified
Parameter
Circuit current
HB voltage
6VREG voltage
CT pin H level voltage
CT pin L level voltage
ICT pin charge current 1
ICT pin charge current 2
ICT pin discharge current 1
ICT pin discharge current 2
ICT charge/discharge ratio 1
ICT charge/discharge ratio 2
ICT charge/discharge ratio threshold
voltage
VTH bias current
OUT output H saturation voltage
PRE output L saturation voltage
PRE output H saturation voltage
Symbol
Conditions
ICC1
VHB
V6VREG
VCTH
VCTL
ICTC1
ICTC2
ICTD1
ICTD2
RCT1
RCT2
VRCT
During driving
IHB=5mA
6VREG=5mA
VCC=12V
VCC=6V
VCC=12V
VCC=6V
VCC=12V
VCC=6V
IBVTH
VOH
VPL
VPH
IO=200mA, RL=1Ω
IO=5mA
IO= -20mA
min
1.05
5.80
3.4
1.4
1.7
1.3
0.11
0.34
12
3
6
-2
Ratings
Unit
typ
max
9
12 mA
1.25
1.40
V
6
6.20
V
3.6
3.8
V
1.6
1.8
V
2.2
2.7
µA
1.8
2.3
µA
0.15
0.19
µA
0.44
0.54
µA
15
18
4
5
6.6
7.3
V
-1
0
µA
0.6
0.8
V
0.2
0.4
V
0.9
1.2
V
Continued on next page.
No.A0082-2/9