|
LA2806M Datasheet, PDF (2/11 Pages) Sanyo Semicon Device – Signal Processor and Power Amplifier IC for Telephone Answering Machines | |||
|
◁ |
LA2806M
Operating Conditions at Ta = 25°C
Parameter
Recomended supply voltage
Operating supply voltage range
Recommended load resistance
Preamplifier input voltage
Symbol
VCC, P.VCC
VCC op, P.VCC op
RL
VIN
Conditions
Power amplifier
Operating Characteristics at Ta = 25°C, VCC = 5 V, f = 1 kHz
Parameter
Quiescent current
[Preamplifier]
Voltage gain
Total harmonic distortion
ALC turnover input voltage
ALC output saturation voltage
Equivalent input noise voltage
ALC range
[Playback equalizer amplifier]
Voltage gain
Total harmonic distortion
Equivalent input noise voltage
[Recording amplifier]
Voltage gain
Output bias voltage
Total harmonic distortion
[LINE amplifier]: RL = 1 kâ¦
Voltage gain
Maximum output voltage
Symbol
ICC
Conditions
VGC
THD
VALC
VOS
VNI
ALC W
â70 dBV input, measured between pins
5 and 8
â40 dBV input, measured between pins
5 and 8
Measured between pins 5 and 8
â40 dBV input, measured between pins
5 and 8
Input short circuited (internal 2.2 kâ¦
resistance)
From ALC ON to THD = 1 %
VGE
THD
VNI
â70 dBV input, measured between pins
2 and 8
â60 dBV input, measured between pins
2 and 8
Input short circuited (internal 2.2 kâ¦
resistance), Flat
VGR
VB
THD
50 k⦠impedance connected to pin 1
ZAC, measured between pins 10 and 2
100 k⦠resistance connected to pin 1
ZDC, measured on pin 2
â40 dBV preamplifier input
VGL
VO max
Measured between pins 10 and 22
Measured between pins 10 and 22,
THD = 1 %
min
57
â68
400
40
57
â7.0
0.4
â1
0.6
Total harmonic distortion
THD
[Power amplifier]: RL = 8 kâ¦, input pin 20
Voltage gain
VGP
Output voltage
PO
â40 dBV preamplifier input
â30 dBV input, measured between pins
20 and 17
THD = 10 %
Total harmonic distortion
THD PO = 100 mW
Input resistance
ri
Ripple rejection ratio
SVRR Rg = 0, fr = 100 Hz, VCCr = â20 dBV
Output noise voltage
VNO Input short circuited, Flat
[Voice-operated switch] Pin 25, R = 20 k⦠applied 5 V.
Sensitivity
Output ON voltage
VOXL
VOXH
V sat
â23 dBV input, f = 800 Hz
â27 dBV input, f = 800 Hz
2 V supplied to pin24
[Control pin voltage]
Pin 26 to 30
Pin 24 (MUTE)
[VREF]
Output voltage
VH Input high-level voltage
VL
Input low-level voltage
VH
Input high-level voltage, supplied via
diode
VREF
26
0.2
10
40
4.5
1.5 (or
VCC + 0.3)
0
1.5
2.05
Ratings
5
4.5 to 7.5
8
0 to 1.0
Unit
V
V
â¦
Vp-p
typ
max
Unit
10
15
mA
59
61
dB
0.5
1.0
%
â64
â60 dBV
500
625 mVrms
1.5
5.0 µVrms
45
dB
59
61
dB
0.5
1.5
%
1.5
5.0 µVrms
â4.0
â1.0
dB
0.8
1.2
V
0.5
1.0
%
0
+1
dB
Vrms
0.5
1.0
%
28
30
dB
0.25
W
0.5
1.0
%
15
20
kâ¦
50
dB
0.1
0.5 mVrms
0.3
V
5.0
V
0.3
V
V
0.8
V
VCCâ0.7
V
2.25
2.45
V
No. 3852 - 2/11
|
▷ |