SI-3000B Datasheet, PDF (2/5 Pages) Sanken electric – 5-Terminal, Multi-Function, Full-Mold, Low Dropout Voltage Dropper Type

qSI-3000B Series
sElectrical Characteristics
Parameter
Symbol
Input Voltage
VIN
Output Voltage
VO
(SI-3025B: Reference
(VREF)
Voltage)
Conditions
Dropout Voltage
VDIF
Conditions
Line Regulation
∆VOLINE
Conditions
Load Regulation
∆VOLOAD
Conditions
Temperature Coefficient of Output ∆VO/∆Ta
Voltage (SI-3025B: Temperature (∆VREF/∆Ta)
Coefficient of Reference Voltage) Conditions
Ripple Rejection
RREJ
Conditions
Quiescent Circuit
Iq
Current
Conditions
IS1
Overcurrent Protection Conditions
Starting Current^*3,4
Conditions
Control Voltage (Output ON) VC. IH
Control Voltage (Output OFF) VC. IL
VC
Control Current
IC. IH
Terminal^*5 (Output ON)
Conditions
Control Current IC. IL
(Output OFF)
Conditions
min.
*2
SI-3157B
typ.
Ratings
max.
27^*1
min.
6^*2,6
(Ta=25°C unless otherwise specified)
SI-3025B
typ.
Unit
max.
27^*1
V
14.92
15.70
16.48
VIN=18V, IO=0.2A
0.5
IO≤0.27A
30
90
VIN=17 to 27V, IO=0.2A
120
300
VIN=18V, IO=0 to 0.27A
±1.5
VIN=18V, IO=5mA, Tj=0 to 100°C
54
VIN=18V, f=100 to 120HZ
3
10
VIN=18V, IO=0A
0.3
0.7
VIN=18V
2.0
0.8
20
VC=2.7V
–0.3
VC=0.4V
2.448
2.550
2.652
VIN=VO+3V, IO=0.2A
0.5
IO≤0.27A
10
VIN=(VO+1) to 27V, IO=0.27A
10
VIN=VO+3V, IO=0 to 0.27A
±0.5
VIN=VO+3V, IO=5mA, Tj=0 to 100°C
54
VIN=VO+3V, f=100 to 120HZ
3
10
VIN=VO+3V, IO=0A
0.3
0.75
When VIN=18V, setting VO=11.7V
0.3
0.7
When VIN=18V, setting VO=15.7V
2.0
0.8
20
VC=2.7V
–0.3
VC=0.4V
V
V
mV
(3025B:
mV/V)
mV
(3025B:
mV/V)
mV/ °C
dB
mA
A
V
µA
mA
*1: VIN(max) and IO(max) are restricted by the relation PD(max)=(VIN-VO)•IO=14(W).
*2: Refer to the dropout voltage.(Refer to Setting DC Input Voltage on page 7.)
*3: IS1 is specified at –5(%) drop point of output voltage VO on the condition that VIN=VO+3V, IO=0.2A.
*4: A foldback type overcurrent protection circuit is built into the IC regulator. Therefore, avoid using it for the following applications as it may cause
starting errors:
(1) Constant current load (2) Plus/minus power (3) Series power (4) VO adjustment by raising ground voltage
*5: Output is ON even when output control terminal VC is open. Each input level is equivalent to LS-TTL. Therefore, it may be directly driven by an
LS-TTL circuit.
*6. When setting output voltage to 5V or less, input voltage needs to be set to 6V or over to operate stably.
29