YFS-30-03-H-05-SB Datasheet, PDF (1/2 Pages) Samtec, Inc – .050[1.27] MULTI-ROW SOCKET ASSEMBLY

REVISION R
DO NOT
SCALE FROM
THIS PRINT
.035 0.89 REF
"B"
REF
"A"
.104 2.64
REF
.095 2.41
REF
IN-PROCESS WITHOUT SOLDERBALLS
SEE NOTE 6
DETAIL 'A'
SCALE 5 : 1
SEE NOTE 16
"F" REF
"G" REF
C
C3-A-MV
((No OF POS -1) x .0500[1.270]))
.0020[.051]
"B"
.145 3.68
"A"
REF
"A"
"B"
02
01
YFSP-XX-01-X _{09 (PIN # = NO. OF ROWS +1)}
R _{YFS-XX-X3-X-XX-SB-XX}
No OF POSITIONS
-20, -30, -40, -50
(PER ROW)
OPTION
-K: KAPTON PAD
(SEE FIG 2, SHT 2)
-TR: TAPE & REEL
(SEE NOTE 17)
LEAD STYLE
-03: PIN / SOLDERBALLS
(USE C-140-03-X, SEE FIG 1)
-L3: PIN / SOLDERBALLS
(LOW INSERTION FORCE)
(USE C-226-03-X)
PLATING SPECIFICATION
-G: GOLD (USE C-XXX-03-G)
(SEE NOTE 7)
-H: HEAVY GOLD (USE C-XXX-03-H)
-E: EXTRA GOLD (USE C-XXX-03-E)
(SEE NOTE 7)
SOLDER BALLS _C1-B,I-XR
-SB: SOLDER BALL
(USE SDB-030-6337)
37% Pb/63% Sn
ROW SPECIFICATION
-05: FIVE (USE YFSP-XX-01-F)
-08: EIGHT (USE YFSP-XX-01-E)
-10: TEN (USE YFSP-XX-01-T)
-06: SIX (USE YFSP-XX-01-6)
(AVAILABLE IN 20 POS ONLY)
-03: THREE (USE YFSP-XX-01-3)
(AVAILABLE IN 20 POS ONLY)
(SEE NOTE 17)
C-XXX-03-X
'A'
C5-B-DC
.134±.003 3.41±0.08
SDB-030-XXXX
SECTION "A"-"A"
.012 0.312
(SEE NOTE 9)
FIG 1
YFS-20-X3-X-08-SB SHOWN
R
SECTION "B"-"B"
NOTES:
1. ^C REPRESENTS A CRITICAL DIMENSION.
2. NOTE DELETED.
3. MAXIMUM BURR ALLOWANCE: .0005[0.013]
4. MINIMUM PUSHOUT FORCE: .5 LB.
5. NOTE DELETED.
C2-B,I-MV 6. CONTACT TO BE FLUSH .002[0.05].
TO BE MEASURED AT ALL FOUR CORNERS.
7. ONE REEL MINIMUM PLATING REQUIREMENT
(85,000 CONTACTS PER REEL)
8. ALL DIMS TO BE SYMMETRICAL ABOUT THE
CENTERLINE WITHIN .001[0.03].
9. .0025[0.064] MAX VARIATION BETWEEN
SOLDERBALLS.
10. REFER TO VISUAL INSPECTION BOARD FOR
SOLDERBALL APPEARANCE CHECKS.
11. THE DISTANCE FROM THE CENTER OF ANY
SOLDERBALL TO THE CENTER OF ANY
ADJACENT INNER PEG SHALL BE
.025 .005[0.64 0.13].
12. NOTE DELETED.
R 13. NOTE DELETED.
14. NOTE DELETED.
15. NOTE DELETED.
16. NO FLASH ALLOWED ON THE PIN TIPS.
C4-B-VS 17. IF -TR OPTION IS NOT SPECIFIED, PARTS TO BE
PACKAGED IN TRAYS. PARTS WITH -03 ROW
SPECIFICATION NOT VALID WITHOUT -TR OPTION.
CRITICAL DIMENSION INSPECTION INSTRUCTION
TABLE
ASSEMBLY OPERATION IN-PROCESS INSPECTION
FILL C-XXX-XX-X
ATTACH SDB-XXX-XXXX
REPRESS SOLDER BALL
FINISHED GOOD
INSPECTION
C2, C3
C3, C4
C5
C1, C2, C3, C5
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
.XX: .01[.3]
2
.XXX: .005[.13]
.XXXX: .0020[.051]
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
MATERIAL:
DO NOT SCALE DRAWING
SHEET SCALE: 2.5:1
INSULATOR: LCP, COLOR: BLACK
CONTACT: PHOS BRONZE
F:\DWG\MISC\MKTG\YFS-XX-X3-X-XX-SB-XX-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: [phone] FAX: [phone]
e-Mail [e-mail] code 55322
DESCRIPTION:
.050[1.27] MULTI-ROW SOCKET ASSEMBLY
DWG. NO. _{YFS-XX-X3-X-XX-SB-XX}
BY: KEVIN B 4/22/99
SHEET 1 OF 2