SSM-133-L-SH Datasheet, PDF (1/4 Pages) Samtec, Inc – .100 2.54 C.L. SURFACE MOUNT SOCKET STRIP

REVISION CT
DO NOT
SCALE FROM
THIS PRINT
NOTES:
SSM-1XX-XXX-XX-XX-XX-X-XX-XX
1. ^C REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM PUSHOUT FORCE: .50 LBS.
3. COPLANARITY TO BE:
-DH: -36 THRU -28 POS: .008[0.20]
-02 THRU -27 POS: .006[0.15]
No OF POSITIONS
-02 THRU -36
(SEE NOTE 8)
OPTION
-TR: TAPE AND REEL
(SEE FIG 8, SHT 4)
(29 POSITIONS MAX)
4.
5.
6.
7.
8.
9.
10.
11.
-SV, SH FULL STRIP STOCK: .008[0.20] (MUST MEET ASSEMBLY SPEC WHEN CUT.
PACKAGE IN TUBES PER SHT 3, TABLE 2. ALL OTHER POSITIONS BULK PACKAGE.
MAXIMUM CUT FLASH: .015[0.38].
NOTCH OF PPP-12 TO BE ORIENTED TOWARD SAME END AS POSITION 1.
ROWS TO BE WITHIN .004[0.10] OF ONE ANOTHER.
-36 MAX POSITION AVAILABLE, -50 FOR STOCK ONLY.
ENDWALL AFTER CUTTING: .033[0.84]±.005[0.13]
DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -LC OPTION
IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS
MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION.
FOR -SV TAIL STYLE: EVEN CUTS LOSE 2 POSITIONS PER CUT; ODD CUTS
PLATING SPECIFICATION
-S: 30µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL.
-L: 10µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL.
-T: MATTE TIN ON CONTACT AND TAIL.
-F: 3µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL.
-STL: 30µ" SELECTIVE GOLD IN CONTACT
AREA, TIN/LEAD (90/10) ON TAIL.
-H: 30µ" SELECTIVE GOLD IN CONTACT
LOSE 1 POSITION PER CUT.
AREA, 3µ" SELECTIVE GOLD ON TAIL.
12. IF POLARIZATION OCCURS AT CENTER POSITION(S) OF BODY, MOVE PICK & -LM: 10µ" SELECTIVE GOLD IN CONTACT
PLACE PAD LEFT OR RIGHT TO NEXT AVAILABLE POSITION.
AREA, MATTE TIN ON TAIL.
13. THIS DIMENSION IS TO BE MEASURED RELATIVE TO DATUM -Z-.
-TM: MATTE TIN ON CONTACT AND TAIL.
-FM: 3µ" SELECTIVE GOLD IN CONTACT
OPTION
-P: PICK AND PLACE PAD
(ONLY AVAILABLE ON -SV,
USE PPP-12, SEE FIG 6, SHT 3)
(SEE NOTE 12)
-K: POLYIMIDE FILM PAD
(SEE FIG 5, SHT 2)
(USE K-DOT-.138-.250-.005)
(NOT AVAILABLE ON -SH AND -DH)
POLARIZATION OPTION
-XX: POSITION TO BE POLARIZED
(USE PK-06-N, SEE FIG 7, SHT 3
FOR POLARIZATION POSITIONS)
(NOT AVAILABLE FOR -BE OPTION)
(NO OF POS x .100[2.54]) -.100[2.54]
.050 1.27
02
REF
36
TAIL SPECIFICATION
-SV: SINGLE VERTICAL (SEE FIG 1)
(USE SSM-XX-S)
-SH: SINGLE HORIZONTAL (SEE FIG 3, SHT 2)
(USE SSM-XX-SH)
C
-DH: DOUBLE HORIZONTAL (SEE FIG 4, SHT 3)
(USE BCH-XX-D)
(NO OF POS x .100[2.54])
±.008[0.20] (CUT TOLERANCE, SEE NOTE 11)
±.005[0.13] (MOLDED BODY TOLERANCE)
MOUNTING OPTION
-LC: LOCKING CLIP
(USE LC-05-TM, SEE NOTE 10)
(FOR -SH AND -DH USE MOLDED TO
POSITION BODIES)
OPTION
-BE: BOTTOM ENTRY
(ONLY AVAILABLE ON -SV)
(USE SSM-XX-S-BE)
(SEE FIG 2, SHT 2)
.100 2.54 REF
01
SSM-XX-S
FLUSH TO .005[0.13] MAX
DETAIL 'D'
SCALE 8 : 1
C ³⁵
C
2 MAX SWAY
(EITHER DIRECTION)
"A"
.290 7.37 REF
CONTACT #1
-Z-
C .295^{+- ..000025} 7.49^{+- 00..015217}
(MEASURE AT BEND)
.18 4.6 REF
C
1°
(SEE NOTE 13)
SEE NOTE 3
"A"
SEE NOTE 9
.050 1.27
(NO OF POS x .100[2.54]) -.200[5.08]
'D'
2 MAX SWAY
(EITHER DIRECTION)
C
4°
(SEE NOTE 13)
LC-05-TM
C
.043±.005 1.09±0.127
-SV IN-PROCESS
FIG 1
-SV: SINGLE VERTICAL ROW
(SSM-1XX-XXX-SV-LC SHOWN)
SECTION "A"-"A"
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
.XX: .01 [0.3]
2
.XXX: .005 [0.13]
.XXXX: .0020 [0.051]
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: [phone] FAX: [phone]
e-Mail [e-mail] code 55322
MATERIAL:
DO NOT SCALE DRAWING
INSULATOR: LCP, UL 94 VO, COLOR: BLACK
CONTACT: PHOS BRONZE
SHEET SCALE: 2:1
DESCRIPTION:
.100[2.54] C.L. SURFACE MOUNT SOCKET STRIP
DWG. NO.
SSM-1XX-XXX-XX-XX-XX-X-XX-XX
F:\DWG\MISC\MKTG\SSM-1XX-XXX-XX-XX-XX-X-XX-XX-MKT.SLDDRW
BY: KOLB
09/11/1998 SHEET 1 OF 4