SSM-125-S-DV Datasheet, PDF (1/2 Pages) Samtec, Inc – .100 C.L. DOUBLE VERTICAL SMT SOCKET STRIP

REVISION AM
DO NOT
SCALE FROM
THIS PRINT
.050 1.27
.100 2.54
REF
C
(No OF POS x .100 [2.54]) .010 [.25]
(No OF POS -1) x .100 [2.54]
.020 0.51 REF
02
.200 5.08
REF
01
2° MAX SWAY
(TYP)
C
NSSM-50-DV
"A"
SEE NOTE 4
SSM-1XX-XXX-DV-XX-XX-X-XX
No OF POSITIONS
-02 THRU -40
(PER ROW) (SEE NOTE 7)
PLATING
-S: 30µ" SELECTIVE GOLD IN CONTACT AREA
MATTE TIN ON TAIL
-L: 10µ" LIGHT SELECTIVE GOLD IN CONTACT
AREA MATTE TIN ON TAIL
-T: MATTE TIN CONTACT AND TAIL
-F: 3µ" FLASH SELECTIVE GOLD
CONTACT, MATTE TIN ON TAIL
-H: 30µ" HEAVY GOLD IN CONTACT AREA
3µ" ON TAIL
-STL: 30µ" SELECTIVE GOLD IN CONTACT AREA
TIN/LEAD (90/10+/-5%) TAIL
-SM: 30µ" SELECTIVE GOLD IN CONTACT AREA
MATTE TIN ON TAIL
-LM: 10µ" LIGHT SELECTIVE GOLD IN CONTACT
AREA MATTE TIN TAIL
-TM: MATTE TIN CONTACT AND TAIL
-FM: 3µ" FLASH SELECTIVE GOLD IN CONTACT
AREA MATTE TIN TAIL
OPTION
-A: ALIGNMENT PIN (SEE FIG 3, SHT 2)
(MOLDED: USE NSSM-XX-DV-XX, 4 POS MIN)
-P: PICK & PLACE PAD (SEE NOTE 5)
(USE PPP-01, SEE FIG 4, SHT 2)
-M: METAL PICK & PLACE PAD (SEE NOTE 5)
(USE LMP-02, SEE FIG 5, SHT 2)
-K: POLYIMIDE FILM PAD
(POS 2 THROUGH 40 - SEE NOTE 5)
(USE K-DOT-.256-.375-.005, SEE FIG 6, SHT 2)
-TR: TAPE & REEL (SEE FIG 8, SHT 2-
29 POSITIONS MAX)
OPTION
-BE: BOTTOM ENTRY
(ONLY AVAILABLE ON -DV)
(FOR -DV SEE NSSM-50-DV-XX)
POLARIZING OPTION
-XX: POSITION TO BE POLARIZED
(USE PK-06-N) (SEE FIG 7, SHT 2)
(NOT AVAILABLE WITH -BE OPTION)
ROW SPECIFICATION
-DV: DOUBLE VERTICAL
(USE NSSM-XX-DV-XX)
MOUNTING OPTION
-LC: LOCKING CLIP
(USE LC-05-TM)(SEE FIG 2)(SEE NOTE 8)
C-137-01-XXX
-Z-
.290 7.37
REF
"A"
FIGURE 2
-LC: LOCKING CLIP OPTION
LC-05-TM
.010 0.25 REF
(No OF POS -2) x .100 [2.54]
2° MAX TOE
(ANY DIRECTION)
C _.292^{+- ..000025} _7.42^{+- 00..0153}
(MEASURE AT BEND)
1° ^C
(SEE NOTE 9)
C
.0060 [.152]
FLUSH TO
.005 [.13] MAX
(SEE NOTE 6)
C
.050 1.27
.056 1.42 REF
.277 7.03 REF
SECTION "A"-"A"
4°
(SEE NOTE 9)
C
.043 1.09
IN-PROCESS
NOTES:
1. C REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM PULLOUT FORCE: .50 LBS
3. MAXIMUM CUT FLASH: .010 [.25].
4. CUT PARTS MAY OR MAY NOT HAVE NOTCHES
5. -P OPTION: 4 POSITION AND UNDER TO BE -T/R
-M OPTION: 3 POSITION AND UNDER TO BE -T/R
-K OPTION: 3 POSITION AND UNDER TO BE -T/R
ALL OTHER POSITIONS WITH -P, -M, -K OPTIONS ARE
TO BE TUBED, UNLESS -TR ORDERED BY CUSTOMER.
6. FLUSH DIMENSION MUST BE INSPECTED ON BOTH ROWS
OF ASSEMBLY.
7. -40 MAX POSITION AVAILABLE, -50 FOR STOCK ONLY
8. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -LC OPTION
IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS
MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION.
9. THIS DIMENSION IS TO BE MEASURED RELATIVE TO DATUM -Z-.
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
.XX: .01 [.3]
2
.XXX: .005 [.13]
.XXXX: .0020 [.051]
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
MATERIAL:
DO NOT SCALE DRAWING
SHEET SCALE: 1:0.4
BODY: LCP UL 94 VO, COLOR: BLACK
CONTACT: PHOS BRONZE
F:\DWG\MISC\MKTG\SSM-1XX-XXX-DV-XX-XX-X-XX-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: [phone] FAX: [phone]
e-Mail [e-mail] code 55322
DESCRIPTION:
.100 C.L. DOUBLE VERTICAL SMT SOCKET STRIP
DWG. NO.
SSM-1XX-XXX-DV-XX-XX-X-XX
BY: KEVIN B 3/8/2000 SHEET 1 OF 2