QSE-040-01-L-D-A Datasheet, PDF (1/5 Pages) Samtec, Inc – .8mm DOUBLE ROW HS SOCKET ASSEMBLY

REVISION BF
DO NOT
SCALE FROM
THIS PRINT
(*= SEE NOTES 12 & 17)
.7875 20.003 (TYP)
(*= SEE NOTES 12 & 17)
C
"A" REF
02
.245 6.22
REF
19 EQ. SPCS
@ .0315 [0.800]
=.599[15.20]
(TYP)
.285 7.24
REF
.150 3.81
REF
01
.0975 2.477
REF
.6250 15.875
REF
.0060 0.152 REF
.0225 0.571
REF
QSE-20-01-D-XX-A
"A"
SEE NOTE 15
QSE-XXX-01-XXX-D-XXX
No OF POSITIONS
-020, -040, -060
*-080, *-100 (PER ROW)
OPTION
-A: ALIGNMENT PINS
(USE QSE-20-XX-D-XX-A)
(NOT AVAILABLE WITH -LC OPTION)
(*= SEE NOTES 12 & 17)
-LC: LOCKING CLIPS(SEE NOTE 14)
(USE LC-08-TM-01, SEE FIG 2, SHT 2)
LEAD STYLE
-01: .1280[3.251]
(NOT AVAILABLE WITH -A OPTION)
-GP: GUIDE POSTS (SEE FIG 4, SHT 3)
(USE QSE-20-01-D-XX-X-GP)
(T & R PACKAGING: 40 POS MAX)
PLATING SPECIFICATION
-K: POLYIMIDE FILM
(USE K-DOT-.325-.450-.005)
(SEE NOTES 8, 11 & 13)
-F: 3µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL
(USE C-126-21-F, T-1G2-01-F)
(SEE NOTE 8)
-L: 10µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL
(USE C-126-21-L, T-1G2-01-L)
-H: 30µ" GOLD IN CONTACT AREA,
3µ" GOLD ON TAIL
(USE C-126-21-H, T-1G2-01-G)
-C: 50µ" ELECTRO POLISHED SELECTIVE
GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
(USE C-126-21-C, T-1G2-01-L)
-STL: 30µ" SELECTIVE GOLD IN CONTACT
AREA, TIN LEAD (90/10 ±5%) ON TAIL
(USE C-126-21-STL, T-1G2-01-STL)
-FTL: 3µ" SELECTIVE GOLD INCONTACT
(SEE FIG 3, SHT 2)
-TR: TAPE & REEL (60 POS MAX)
(SEE FIG 8, SHT 5)
(40 POS MAX -GP OPTION)
-FL: FRICTION LOCKS
(SEE FIG 5, SHT 3)
(NOT AVAILABLE WITH -GP)
-RT1: RETENTION OPTION
(MUST USE -A OPTION)
(USE QSE-20-01-D-XX-A-RT1 &
SUB-SC-05-01-FF)
(SEE FIG 6, SHT 4)
(NOT AVAILABLE WITH -LC, -GP, OR -FL)
(NOT AVAILABLE WITH -100 POS)
-L: LATCHING OPTION (40 POS MAX)
(SEE FIG 7, SHT 4)
(MUST USE -A OPTION)
(NOT AVAILABLE WITH -LC, -GP, -FL,
OR -RT1)
AREA, TIN LEAD (90/10 ±5%) ON TAIL
(USE C-126-21-FTL, T-1G2-01-FTL)
-LTL: 10µ" SELECTIVE GOLD IN CONTACT
AREA, TIN LEAD (90/10 ±5%) ON TAIL
(USE C-126-21-LTL, T-1G2-01-LTL)
-S: 30µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL
ROW SPECIFICATION
-D: DOUBLE
(USE QSE-20-XX-D-XX)
(USE C-126-21-S, T-1G2-01-L)
No OF BANKS
.038 0.95
REF
.725 18.42
REF
"A"
"B" REF
T-1G2-01-XXX
CL
NOTES:
1. C REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM CONTACT RETENTION: 8 OZ
3. MINIMUM GROUND PLANE RETENTION: 8 OZ
4. PARTS ARE MOLDED TO POSITION.
5. DELETED.
6. MAXIMUM VARIANCE: .002[0.51].
7. DIMENSION APPLIES TO CONTACTS & GROUND PLANE.
8. -L PLATING CAN BE SUBSTITUTED FOR -F PLATING, -G PLATED GROUND
PLANE CAN BE SUBSTITUTED FOR -F PLATED GROUND PLANE.
9. GROUND PLANE PRESS HEIGHT MUST BE .003 [0.08] LESS THAN THE MAX HEIGHT
OR .001 [0.03] GREATER THAN THE MINIMUM HEIGHT OF THE SOCKETS.
10. MINIMUM SUB-SC-05-01-XX RETENTION: 1 LB IN BODY.
11. MAY SUB C-126-01-XXX FOR C-126-21-XXX.
12. FOR NEW APPLICATIONS REQUIRING THESE POSITIONS, PLEASE CONTACT
SAMTEC INTERCONNECT PROCESSING GROUP.
13. FOR -080, -100 POSITIONS USE C-269-11-XXX. DO NOT SUB C-126.
14. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -LC OPTION
IS NOT COMPATIBLE WITH AUTO PLACEMENT.SAMTEC RECOMMENDS
MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION.
15. SIDE WALLS ARE RIBBED AS NECESSARY TO CONTROL BOW.
16. CHECK ONCE PER BANK ALTERNATING SIDES FOR MULTIPLE BANK PARTS.
17. AVAILABLE FOR EXISTING CUSTOMERS ONLY.
.035 0.89 REF
.120 3.05
REF
.105 2.67
REF
.017±.005 0.43±0.13
(SEE NOTE 16)
.0030 0.076 REF
.165^{+- ..000051} 4.19^{+- 00..1033}
C
.064 1.62 REF
C
.1280^+- _..00001300 3.251^+- _00..002756
(SEE NOTE 6 & 7)
SEE TABLE 1
C
.007 0.18 REF
FIG 1
-A: ALIGNMENT PIN OPTION
(QSE-060-01-XXX-D-A SHOWN)
SECTION "A"-"A"
.295 7.49
C-126-21-XXX
(SEE NOTE 13)
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
.XX: .01[.3]
2
.XXX: .005[.13]
.XXXX: .0020[.051]
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
MATERIAL:
DO NOT SCALE DRAWING
INSULATOR: LCP, UL94V-0; COLOR: BLACK
CONTACT: PHOS BRONZE
GROUND PLANE: PHOS BRONZE
SHEET SCALE: 1.5:1
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: [phone] FAX: [phone]
e-Mail [e-mail] code 55322
DESCRIPTION:
.8mm DOUBLE ROW HS SOCKET ASSEMBLY
DWG. NO.
QSE-XXX-01-XXX-D-XXX
F:\DWG\MISC\MKTG\QSE-XXX-01-XXX-D-XXX-MKT.SLDDRW
BY: ERIC M 05/20/1999 SHEET 1 OF 5