QRM8 Datasheet, PDF (1/4 Pages) Samtec, Inc – .8MM Q-RATE TERMINAL ASSEMBLY

REVISION J
DO NOT
SCALE FROM
THIS PRINT
DESIGNED AND DIMENSIONED
IN MILLIMETERS [INCHES]
01
4.60 .181
02
"A" REF
"B" REF
24.80 .976 (TYP)
C
0.80 .031 (TYP)
(TOL NON ACCUM)
C
"C"
"A"
"M" REF
QRM8-XXX-XX.X-X-D-XX-A-XX
No OF POSITIONS
-026, -052, **-078
(-018, -036, **-054 FOR -DP ONLY)
LEAD STYLE
-02.0 = 2mm (SEE FIG. 1)
103
-05.0 = 5mm (SEE FIG. 3, SHT 2)
-07.0 = 7mm
OPTIONS
-K: POLYIMIDE FILM PAD
-TR: TAPE & REEL
(SEE NOTE 4)
-GP: GUIDE POST
(SHEET 3, FIG 4)
(SEE NOTE 8)
OPTIONS
-A: ALIGNMENT PIN
PLATING SPECIFICATION
-L: LIGHT SELECTIVE GOLD / MATTE TIN
(USE T-1M53-XX.X-L & T-1G38-XX.X-L)
-S: SELECTIVE GOLD / MATTE TIN
(USE T-1M53-XX.X-S & T-1G38-XX.X-S)
104
OPTION
(IF NOT APPLICABLE, LEAVE BLANK)
-DP: DIFFERENTIAL PAIRS
(SHEET 4, FIG 5)
ROW SPECIFICATION
-D: DOUBLE
* = NOT AVAILABLE IN -02.0 LEAD STYLE
C
C
2.200^+- _00..200500 .0866^+- _..00007290
0.44 .02 REF
T-1G38-XX.X-X
(SEE TABLE 2)
0.05 .002
0.46 .018 REF
0.82 .032 REF
1.00 .039
REF
0.50 .020
REF
* = NOT AVAILABLE IN 02.0 LEAD STYLE
0.23 .009 REF
(TYP)
"D" REF
C
"C"
CL
C
0.80 .031 (TYP)
(TOL. NON-ACCUM)
T-1M53-XX.X-X
"A"
(SEE TABLE 2)
"F" REF
QRM8-XXX-XX.X-DV-XX
(SEE TABLE 2)
1.32 .052
REF
C
SEE TABLE 6
0.78 .031 REF
(SEE NOTE 5)
CL
"E" ^C
1.00 .039 REF
C
3.67 .145
(SEE NOTE 5, 6, 7 & 9)
CL
'B'
DETAIL 'B'
SCALE 4 : 1
SECTION "A"-"A"
SCALE 6 : 1
FIG 1
NOTES:
(QRM8-052-02.0-X-D-A SHOWN) _1. C _{REPRESENTS A CRITICAL DIMENSION.}
2. BURR ALLOWANCE: 0.038[.0015] MAX.
3. MINIMUM PUSHOUT FORCE: SIGNAL: 1.60 N [.4 LB.]; GROUND PLANE: 4.44 [1LB]
4. PARTS TO BE PACKAGED IN TRAYS, UNLESS -TR OPTION IS SPECIFIED.
-054 & -078 POSITION NOT AVAILABLE IN TAPE AND REEL.
5. DIMENSION APPLIES TO CONTACTS & GROUND PLANE.
6. GROUND PLANE PRESS HEIGHT MUST BE .08 [.003] LESS THAN THE MAX HEIGHT
OR .001 [.03] GREATER THAN THE MINIMUM HEIGHT OF THE TERMINAL.
7. MAX VARIANCE OF 0.05 [.002].
8. PARTS WITH THE -GP OPTION MUST MATE TO -GP OPTIONED QRF8 PARTS AND
PARTS WITH NO -GP OPTION MUST MATE TO NON -GP OPTIONED QRF8 PARTS.
9. GROUND PLANES INSERTION AIR PRESSURE TO BE SET AT 20-25 PSI.
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN
MILLIMETERS [INCHES].
TOLERANCES ARE:
DECIMALS
ANGLES
X.X: 0.3 [.01]
2
X.XX: 0.13 [.005]
X.XXX: 0.050 [.0020]
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: [phone] FAX: [phone]
e-Mail [e-mail] code 55322
MATERIAL:
DO NOT SCALE DRAWING
INSULATOR: LCP, COLOR: BLACK
TERMINAL & GROUND PLANE: PHOS. BRZ.
SHEET SCALE: 2:1
DESCRIPTION:
.8MM Q-RATE TERMINAL ASSEMBLY
DWG. NO.
QRM8-XXX-XX.X-X-D-XX-A-XX
F:\DWG\MISC\MKTG\QRM8-XXX-XX.X-X-D-XX-A-XX-MKT.SLDDRW
BY: CLAY W
8/27/2008 SHEET 1 OF 4