MEC1-108-02-S-D-A Datasheet, PDF (1/2 Pages) Samtec, Inc – 1mm MINI-EDGE CARD ASSEMBLY

REVISION AD
.109 2.77
REF
DO NOT
SCALE FROM
THIS PRINT
.275 6.99
REF
C6
.050 1.27
(No OF POS -1) x .03937 [1.00]
C1
({(No OF POS +2) x .03937 [1.00]}
+ .100 [2.54])
.007[.18]
.005[.13]
.026 0.66 REF
02
16
40
FLOW INHIBITORS
AT VENDOR DISCRETION
MEC1-1XX-XX-XX-D-XX-XX
No OF POSITIONS
05, 08, 20, 30, 40 , 50, 60 & 70
(PER ROW, SEE TABLE 2)
CARD THICKNESS
-02: .062 [1.58] THICK CARD
(USE MEC1-XX-S-D-X-X)
OTHER OPTIONS
-LC: LOCKING CLIP
(SEE FIG. 2)(USE LC-05-TM)
-A: ALIGNMENT PIN
(MOLDED, SEE FIG. 4, SHT. 2)
(USE MEC1-XX-X-D-X-A)
-K: POLYIMIDE FILM PAD
(SEE FIG. 6, SHT. 2)(USE K-500-300)
-TR: TAPE & REEL PACKAGING
(N/A IN 70 POSITION)(SEE FIG. 5, SHT. 2)
.072 1.83 REF
15
1.5° MAX SWAY
39
01
(ANY DIRECTION)
MEC1-XX-X-D-X-X
PLATING SPECIFICATION
-F: FLASH GOLD (USE C-113-02-F)
-L: LIGHT GOLD (USE C-113-02-L)
POLARIZED OPTION (SEE TABLE 2)
-BLANK: BODY IS POLARIZED
-NP: NO POLARIZATION (-05 THRU -30 ONLY)
(USE MEC1-XX-X-D-N-X)
-S: SELECTIVE GOLD (USE C-113-02-S)
FIG. 1
-FM: FLASH GOLD (USE C-113-02-F)/
MATTE TIN TAILS
-LM: LIGHT GOLD (USE C-113-02-L)/
ROW SPECIFICATION
-D: DOUBLE ROW
(No OF POS +2) x
MEC1-120-02-X-D SHOWN
MATTE TIN TAILS
-SM: SELECTIVE GOLD (USE C-113-02-S)/
(USE MEC1-XX-X-D-X-X)
.03937 [1.00] REF
SEE NOTE 5
MATTE TIN TAILS
C7 .020 0.51
.160 4.07 REF
"A"
.350 8.89
REF
"A"
.079 2.00
C2
.356^+- _..000024 9.04^+- _00..0150
C-113-02-XX
90°±3°
.334 8.49
.006 0.15 REF
.320 8.13
REF
SEE NOTE 2
.030 0.75
SECTION "A"-"A"
02
40
PACKAGING VIEW
IN-PROCESS
(FILL STEP)
C4
.535^+- _..000005 13.59^+00..0103
NOTES:
1. MINIMUM PUSHOUT FORCE: 10 oz.
C3 2. COPLANARITY: POS -05 THRU -26: .004 [.10]
POS -27 THRU -70: .006 [.15]
3. C REPRESENTS A CRITICAL DIMENSION.
4. PACKAGE ALL POSITIONS IN TUBES.
(WITH -K OPTION, USE PT-1-24-01-70 TUBE & TP-29 TUBE PLUG)
(WITHOUT -K OPTION, USE PT-1-24-01-69 TUBE & TP-07 TUBE PLUG)
5. MAXIMUM CUT FLASH: .010; FLASH NOT TO EXTEND BELOW LEADS.
6. MAXIMUM ALLOWABLE BOW: .002 INCH/INCH AFTER ASSEMBLY.
7. MAXIMUM BURR: .003[.08], BURR DIRECTION TO BE OPPOSITE OF SOLDER PAD AREA
01
39
MEC1-XX-X-D-N-X
-NP: NON-POLARIZED OPTION
(AVAILABLE ON -05, -08, -20 & -30 POS. ONLY)
(SHOWN: MEC1-120-02-X-D-NP)
FOR -K OPTION
TUBE: PT-1-24-01-70
PLUG: TP-29
NO -K OPTION
TUBE: PT-1-24-01-69
PLUG: TP-07
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
.XX: .01 [.3]
2
.XXX: .005 [.13]
.XXXX: .0015 [.038]
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
MATERIAL:
DO NOT SCALE DRAWING
INSULATOR:
VECTRA E130i COLOR: BLACK
SHEET SCALE: 1.5:1
CONTACT:
BeCu 190 HM
c:\enterprisevault\DWG\MISC\MKTG\MEC1-1XX-XX-XX-D-XX-XX-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: [phone] FAX: [phone]
e-Mail: [e-mail]
code: 55322
DESCRIPTION:
1mm MINI-EDGE CARD ASSEMBLY
DWG. NO.
MEC1-1XX-XX-XX-D-XX-XX
BY: KEVIN B 5/11/2000 SHEET 1 OF 2