IPD1-02-D Datasheet, PDF (1/2 Pages) Samtec, Inc – .100 SHROUDED CONTACT BODY

REVISION G
DO NOT
SCALE FROM
THIS PRINT
.050
C2
FIG. 1
IPD1-06-D SHOWN
C1
((No OF POSITIONS x .100) + .055)
.007
.003
.078±.010
.035±.010
.220
.0775
(4 PLCS)
.350 .100
"A"
.0723
(SEE NOTE 14)
'H'
SEE NOTE 8
.08
.505^+- _..000005
SEE NOTE 11
.050 (TYP)
'C'
C3
((No OF POSITIONS -1) x .100)
.002
.003
02 01
C4
"A"
.250±.002
07
'B'
'A'
"B"
GATE PADS
(SEE NOTE 9)
.0923
(SEE NOTE 14)
'F'
C5
.4800±.0020
.045
IPD1-XX-D-X
No OF POSITIONS
-02 THRU -25
(PER ROW)
[SEE FIG. 2 FOR -02 POSITION]
*NOT RELEASED FOR PRODUCTION
POLARIZATION OPTION
-P: POLARIZED
(NOT AVAILABLE WITH
-K OPTION)
(LEAVE BLANK FOR
NO POLARIZATION)
(SEE FIG. 3)
G *-K: KEYED POLARIZATION
(NOT AVAILABLE WITH
-P OPTION)
(SEE SHEET 2, FIG. 4)
NOTES:
ROW SPECIFICATION
1. ^C REPRESENTS A CRITICAL DIMENSION.
-D: DOUBLE
2. SAMTEC LOGO SHALL APPEAR AT ONE LOCATION ON SURFACE SHOWN,
APPROXIMATELY .150 x .094 (BOTH SIDES).
3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH A LETTER
DESIGNATION LOCATED WHERE SHOWN.
4. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN .002 OFF THE
SURFACE OF THE PART.
5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
6. MAX ALLOWABLE BOW: SEE TABLE 1. BOW TO BE MEASURED AT MIDLINE OF PART.
7. PART TO BE SYMMETRIC ABOUT THE CENTERLINE WITHIN +/-.002, UNLESS
OTHERWISE STATED.
8. NUMBER OF POSITIONS (PER ROW) TO BE SHOWN IN THIS AREA EXCLUDING
2, 3 AND 4 POSITIONS. SIZE AND DEPTH SIMILAR TO POSITION 1 INDICATOR.
9. GATE PADS MUST BE RECESSED .005.
10. END CORES ARE POLARIZED. CONFIRM GEOMETRY RELATIVE TO POSITION 1
INDICATOR & GATE PADS.
G 11. POSITION 1 INDICATOR TO BE RAISED .005 MAX, NOT PRESENT ON 2 POSITION
OPTION.
12. SPECIFIED POSITIONS TO BE IDENTIFIED WHERE SHOWN (NOTE 4 APPLIES).
13. MOLD DESIGNER HAS DISCRETION OVER RIB LOCATION. STEEL PRINT SETUP
SHEET MUST SHOW RIB CONFIGURATION FOR EACH PART NUMBER.
14. PART MUST DRAFT INWARD FROM BOTTOM TO TOP OF STACK.
15. ALL DIMENSIONS TO BE SYMMETRIC ABOUT CENTERLINE WITHIN .0015
UNLESS OTHERWISE STATED.
FIG. 3
IPD1-06-D-P SHOWN
(SAME AS FIG. 1, EXCEPT AS SHOWN)
02 01
"J"
'E'
PARTING LINE
07 "J"
SEE NOTE 2
SEE NOTE 3
"B"
SECTION "A"-"A"
.100±.005
'D'
.255
.059^+- _..000012 C6
.020 (2 PLCS)
'G'
12 11
08 07
SEE NOTE 12
.050 (TYP)
06 05 04 03 02 01
.050
.112
.082
SECTION "B"-"B"
.255
SECTION "J"-"J"
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
.XX: .01 [.3]
2
.XXX: .003 [.08]
.XXXX: .0015 [.038]
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
MATERIAL:
DO NOT SCALE DRAWING
ZYTEL 103FHS, COLOR: WHITE
SHEET SCALE: 2:1
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: [phone] FAX: [phone]
e-Mail: [e-mail]
code: 55322
DESCRIPTION:
.100 SHROUDED CONTACT BODY
MAX REGRIND: 25%
MAX FLASH ALLOWED: .004
MAX GATE VESTIGE: .002
c:\enterprisevault\DWG\MISC\MKTG\IPD1-XX-D-X-MKT.SLDDRW
DWG. NO.
IPD1-XX-D-X
BY: CHAD F 03/05/2002 SHEET 1 OF 2